4 ms·
It's step four. Forget about the printer for weeks until I need it again Inkjets work reliably when used regularly. And tend not to when they aren't. And this
by brudgers 6y ago
It's step four.
Forget about the printer for weeks until I need it again
Inkjets work reliably when used regularly. And tend not to when they aren't. And this is even more the case when the inkjet is unplugged because of those annoying maintenance cycles in the middle of the night. Or in the middle of the day that result in an empty ink message despite not printing anything.
I went through the same thing for years. A cycle of dread where I avoided printing because half time printing seemed to mean a trip to the office supply store and twenty or sixty dollars in ink cartridges with the anticipation I would have a similar experience next time.
Now I print regularly because I know it's ok and have had zero issues since April of 2018 when I realized "oh fuck, I bought another printer." But it's killer feature is third party ink support - OEM cartridges can be reset and refilled with inks that are good enough and the inks can be bought in bulk...where bulk means 100ml at a time for as little as $2/oz (or ~$0.07/ml).
When it runs out of ink, I can reset and refill the empties, top off the non-empties, swap out the cartridges, and put everything away and clean up the sink in about twenty minutes. Less time than going to the store and back. Since I have two full sets of cartridges, I can do the swap out before the refill and empties hold me up less than five minutes in practice.
Sure, there's a big part of me that doesn't feel that any of this should be necessary because...well it's a computer. On the other hand, I can't just use my laptop and close the lid without plugging it in. YMMV.
- harha 6y agoIf that is the only problem, wouldn't laser printers have fixed it? There's a ton of other things that don't work, e.g. paper jams. With the multi-function devices this gets even worse. Not using a device all the time should be a use-case that is accounted for. Imagine having to service a car every time it stands still for a few weeks, nobody living in a city would have a car. Of course, there's a lot of complexity and moving parts involved, but it just seems like a problem that could have been fixed by now. The rise of home office makes it very annoying, before that most people I know would just print everything at the office where someone manages the printer, also some places have a 7/11 around the corner with one of those big printers, so that really helps. It would be nice if someone could make a "fair printer" at a reasonable premium, with good (open source) drivers, cartridges for different use-cases, replaceable and easy to clean parts and thinking of the biggest problems, e.g., an easy way to understand and fix paper jams. I doubt the way financing or corporations work we'll see that happening.
- brudgers 6y agoPaper jams are also related to use. Paper is dimensionally unstable. It swells and shrinks with changes in humidity. In a stack of paper the exposed top sheet will change more than the sheet below it. The edges of each sheet will change more than the center. Additionally paper has a grain structure and expands more in one axis than the others. Humidity also changes the thickness of paper. That’s the nature of paper. Most people, and for a long time I was one of them don’t have a good working model of paper as a material. In part because mechanical printing was not common until thirty years ago. In part because in the first part of the PC revolution printing was more an everyday thing since online publishing was rarely a viable alternative. After I wrote my previous comment, I fleshed out an idea it touches on tangentially. Printers are not computational artifacts. Little more so than a dishwasher with a microprocessor. Though we tend to think of them as part of a computer, they act directly in meat space. Directly on paper with ink or toner. Laser printers are less reliable because we print less. The old workhorse printers were workhorse printers because they were used so heavily that paper didn’t have much time to swell in bad ways. There are printing methods that are good for infrequent use. Fanfold paper tractor fed through an impact printer is nearly bulletproof and dies gracefully as the ribbon ink depletes. But they are noisy, bulky, slow, feature poor, and inflexible. However most understand ESC2 and writing control software is accessible from any language that can send bytes to a port.
- gregmac 6y agoI took a tour of HP's Boise test lab [1] a few years ago, and the biggest take-away from that for me was that (in their opinion) paper quality is one of the biggest factors in printer reliablity. The test lab includes lots of neat things: an RF chamber, acoustic chamber (in a dedicated separate vibration-isolated building), a couple climate simuation rooms (humid, cold), a bunch of robot arms that open/close drawers or use touchscreens/keypads. (Here's a 5-min video tour [2] of it if you're interested.) Despite all that they were quite proud of their a massive inventory of paper from all over the world and testing they did with it. This included environmental (humidity/temp) testing after acclimatizing the paper for several days. They even went out of their way to get paper mills to custom create some of the crappiest papers they'd run across. I think the explanation was basically poor quality, rough paper leaves particles all over everything and causes rollers, drums etc to wear out faster. Depending on your usage, it's at least worth considering when you're buying paper and looking at saving a few dollars on the cheaper stuff. [1] https://garage.hp.com/us/en/business/boise-test-lab-hp-printers.html https://garage.hp.com/us/en/business/boise-test-lab-hp-print... [2] https://vimeo.com/242827801/8322d83960 https://vimeo.com/242827801/8322d83960
- magicalhippo 6y ago> Inkjets work reliably when used regularly. My dad had a HP Deskjet 720 and after several years of using it, it had been sitting for at least 2 years without a single print or maintenance. Then one day I needed it for a school project, with all its colors due to some graphs. Printed a simple test page with some colors twice, then the colors were back in action. Successfully printed 20 or so color pages after that without issue. So clearly inkjets that doesn't dry out was a solved problem, however I realize that doesn't exactly drive ink or printer sales so yeah. These days I just have a monochrome laser printer at home for the two-three times a year I need it. Always just works, no fuzz.
- tasty_freeze 6y agoI have a brother MFC-J6520DW scanner/printer. It is inexpensive and I bought it mainly for its large format scanning capability. Problem #1: I don't use it much. But every night (or two?) it does a self cleaning cycle which uses up some ink apparently. Despite saying the ink cartridges saying "500 prints", I might actually make 50 pages before it runs out of ink after a few months. Problem #2: I only ever need it for black and white, yet I have to buy expensive color cartridge sets as it refuses to print B&W pages if it is out of color. And it runs out of color despite my not using it because of problem #1 above. Problem #3: After it gives the ink low warning, if I ignore it for a while until it actually starts making splotchy prints, when I put the new ink cartridges in, I have to literally print dozens of test pages before the quality is acceptable again. I have no idea what is going on there. By that time the B&W cartridge will report it is at 60% capacity. Once this set runs out in a few months, I've already decided to get a monochrome laser printer, and regret not doing it long ago.
- brudgers 6y agoThe copyright on the 750c manual is 1997. It was a different era. The printer market was in a different place. And HP was a different company. Occasional home use is not the market segment it was twenty plus years ago. My 550c didn’t clog either. One of the the big changes is inks print and dry faster. Those early inkjet inks needed thirty seconds or so to dry and similar times to print...at best - a full page of color in the 1990’s was minutes per page.