10 ms·
Leveraging a 3D printer “defect” to create a new quasi-textile
- bigiain 6y agoHmmm, I wonder if a dual extruder printer using conductive filament in one nozzle could print flexible fabric circuit boards? Embed cabling for leds/elwire directly into the fabric?
- Firerouge 6y agoI suspect it would be exceedingly difficult to get enough conductive materials in the mix, while also sufficiently purging to insulate between different traces/threads. Perhaps printing an outfit entirely from conductive threads could be used to create a grounded Faraday cage suit/dress.
- bigiain 6y agoPurging might not be a probelm with dual extruders? The "trick" that makes it possible might not work without all the filament coming out of a single extruder nozzle in a connected spiderweb though...
- noodlesUK 6y agoSuch conductive garments already exist in the form of fencing lamés, and other special-purpose wear which is used by electricians. A fun fact is that whilst wearing a fencing lamé, one is generally impervious to tasers and stun guns.
- anonymfus 6y agoAlso as a cheaper alternative one can wrap themself in foil tape.
- pontifier 6y agoThis is fantastic. I'm reminded of the 3D printed broom from a few years ago. I remember being blown away in a similar fashion then. This type of under extrusion can create very thin filaments, but the Gcode to generate these structures isn't easy to create with the traditional model=>slicer=>Gcode software stack. I've been out of the loop for a couple of years though, so I'm interested to know if this has evolved much.
- meekmind 6y agoI think it's fair to say there have been sweeping changes.
- rhklein 6y agoI wrote a G-code Importer for Blender recently. Having access to the toolpaths directly lets you do some interesting things conventional slicers can't do. https://github.com/Heinz-Loepmeier/Blender-Gcode-Import/wiki https://github.com/Heinz-Loepmeier/Blender-Gcode-Import/wiki I've been experimenting with storing extrusion multiplier info inside Blender to make weighted extrusion values based on a texture.
- curiousllama 6y agoI wonder if they just used a custom slicer. In undergrad, I wrote my own slicer and used it to do silly things (less "can I make this?" than "What would happen if?"). I would imagine they took a similar (though, obviously, much more intelligent) approach here, just thinking directly in terms of slicer features, rather than in terms of models.
- thdrdt 6y agoGcode for this type of 3d printer is very easy to understand and generate. Some years ago I did some experiments with 3d printing in 3d (printing wire frames in 3d). But it takes time to get the feed rates and print speeds right. Edit: an example of wireframe printing: http://www.creativeapplications.net/wp-content/uploads/2014/09/bottle-with-printing.jpg http://www.creativeapplications.net/wp-content/uploads/2014/...
- Munksgaard 6y agoOut of curiosity, what printer would they be using for something like this? I've been considering getting a 3D-printer for a while, but I don't know enough to decide which one to get.
- typerandom 6y agoIt looked like they were using the Prusa I3 MK3S.
- klohto 6y agoJust get Prusa. It’s used both by professionals and amateurs. In case it won’t be enough for your use, you will already know enough details about 3D printing to choose your next printer.
- cannedslime 6y agoIf you have the money and want a high quality FDM printer, buy a prusa. If you are on a budget get something like an Ender-3
- curiousllama 6y agoThis model is what I first got, and liked. Fun to put together and mess with. Won't print anything crazy, but will be plenty fun to play with. https://shop.prusa3d.com/en/upgrades/183-original-prusa-i3-mk25smk3s-multi-material-2s-upgrade-kit-mmu2s.html# https://shop.prusa3d.com/en/upgrades/183-original-prusa-i3-m...
- lsllc 6y agoI did an Ask HN [0] on this topic a few months ago and the answer was a Prusa I3 MK3S if you can afford it and the Creality Ender 3 if your budget is smaller. I did get the Prusa I3 MK3S and it's just incredible, I'm astounded by the quality of the prints and the printer itself. I've already designed a number of parts in Fusion360 and printed them with a variety of different filaments (Flex, PLA, PETG) and having a lot of fun creating things! [0] https://news.ycombinator.com/item?id=24032659 https://news.ycombinator.com/item?id=24032659
- kevin_thibedeau 6y ago
- chrischen 6y agoVery interested in the badminton shuttlecock implementation. Wonder if it can be superior to current plastic shuttlecocks.
- londons_explore 6y agoIs the extruder speeding up and slowing down for each "blob" in the texture? Or is the extruder going constant speed and you're relying on surface tension to make the blobbyness?
- rhklein 6y agoMost like some postprocessing in the gcode to multiply the extrusion rate by some factor for each blob.
- curiousllama 6y agoProbably some combination. They used a cheap printer - I can't imagine those little prusa motors and gears are particularly precise with high-frequency, micro changes, even if they can get good consistency
- lylecheatham 6y agoYou'd be surprised actually! Prusa uses no gearing between the motor and the primary drive gear and it's a 200 step/rev NEMA 17. You can transmit high frequencies quite easily, and I've actually seen bad stepper motors with high cogging torque transmit that periodic torque as an extrusion defect into walls with the correct thickness.
- londons_explore 6y agoI've run a 3d printer with the extrusion rate way down before (to try and produce very thin surfaces), and the results were far less consistent. I got big holes in my parts and massive dribbles and blobs in other places. I wonder how these results can be so so so much better in comparison?
- corty 6y agoFrom my limited expirience, temperature of the extruded material must be in some narrow window, too cold or too hot and it will clump. Even within the window, the production of sticky hairs (what one would aim for in this case) varies a lot with temperature. I can also imagine that the material plays a huge role, but I cannot say because I've only really used PLA.
- jstanley 6y agoThe desired result is that you get a series of pulses of extrusion rather than random under-extrusion, so if you can't get consistent pulsing by adjusting temperature and extrustion rate, you could always hack Marlin to do it on purpose. I expect that is what they've done.
- himinlomax 6y agoIt looks like it works not by constantly underextruding, but only intermittently. The parts where the strands join are overextruded if anything.
- lylecheatham 6y agoI'm pretty sure it's actually just a continuous under extrusion. It becomes periodic in nature because material gathers under the nozzle and then it hits the blob from the previous layer and gets pulled off. It's a similar effect to how droplets form and fall off of your faucet when the flow rate is low. This also leads to the diagonal angles seen as the Z-height goes up. It's usually hard to get this to happen consistently, which they've done quite well. I've got no citations, but I worked in FDM Additive Manufacturing for a few years, and spent 4 months of that designing extruders for a name brand company.
- kallistohak 6y agoFinally someone solved the problem of sold out toilet paper in the pandemic
- curiousllama 6y agoPLA toilet paper - It has holes, no absorbtion, sharp edges, and takes an hour per square to print. Sign me up!
- NikolaeVarius 6y agoI transitioned to sea shells to fix this problem
- snovv_crash 6y ago3 3D printed sea shells?
- NikolaeVarius 6y agoWood infused for that all natural feeling
- pstuart 6y agoBidets are a worthwhile investment.
- eecc 6y agoRead somewhere that there’s a whole field of research dedicated to mathematically designed, non-flat textiles. If you think of it, all we do currently is cut and sew flat tiles of deformable cloth to approximate whatever curvature, but if you can print the material with the curvatures embedded it’s an interesting path to explore
- LeifCarrotson 6y agoNike Flyknit shoes have this technology: https://www.nike.com/flyknit https://www.nike.com/flyknit They weave different densities and materials in different sections of the upper to make some areas stronger, some more breathable, some stretchy, etc. You may have seen it referenced in some of the recent furor over the Next% carbon midplate.
- nicwolff 6y agoNorth Sails' 3Di tech? They make precisely curved sails for racing yachts. https://www.northsails.com/sailing/en/innovation/3di-technology https://www.northsails.com/sailing/en/innovation/3di-technol...
- jeffrallen 6y agoWow. Mind blown.
- mrfusion 6y agoThis seems cool but my imagination doesn’t seem to be working today. I can’t seem to think of any interesting applications of this.
- 2muchcoffeeman 6y agoThere is literally a video with applications in the link.
- mrfusion 6y agoI skimmed it. I guess I missed that.
- eigenvalue 6y agoSeems to me like this works on the same principles as these big machines used to make plastic netting for fruits: https://www.alibaba.com/product-detail/Fruit-net-machine_62016415988.html?spm=a2700.7724857.normalList.1.23985e501eqpye&s=p&fullFirstScreen=true https://www.alibaba.com/product-detail/Fruit-net-machine_620... But $300 is a lot more accessible than $5,000, and it's a lot more customizable.
- Cactus2018 6y agoThere are some great 'how its made' videos on youtube under combinations of search terms like circular loom weaving machine Plastic netting for fruits https://www.youtube.com/watch?v=4FG2d97nxSg https://www.youtube.com/watch?v=4FG2d97nxSg Lexus CF printing promo https://www.youtube.com/watch?v=kttvDaUIWCs https://www.youtube.com/watch?v=kttvDaUIWCs