4 ms·
> When the water is gone the temperature of the pot starts to rise. Water-to-rice ratios are important. America's Test Kitchen has a good video on the topic, e
by throw0101a 6y ago
> When the water is gone the temperature of the pot starts to rise.
Water-to-rice ratios are important. America's Test Kitchen has a good video on the topic, especially if you're using a pot and not a rice cooker:
* https://www.youtube.com/watch?v=JOOSikanIlI https://www.youtube.com/watch?v=JOOSikanIlI
* https://www.youtube.com/watch?v=DJFU7ezipbg https://www.youtube.com/watch?v=DJFU7ezipbg
The rice actually only 'needs' a 1:1 ratio, but you need to put in extra to deal with evaporation; brown rice needs more-extra because it takes longer to cook (the bran slows absorption), and the longer cooking time leads to more evaporation.
TL;DR: ignore what's on the bag/box, and for every cup of rice add one cup of water (1:1, 2:2, 3:3), and then a fixed amount of extra overhead for evaporation.
- dogma1138 6y agoRinsing the rice and letting it sit for 30-60min absorbing some moisture then a 1:1.25 ratio is by far the best method I’ve used. I also let it steam in its own heat for the last 10min or so of cooking since the temp won’t rise it won’t overcook the rice but it will prevent any rice from being undercooked or from the rice at the bottom form burning. If I don’t have the tome to rinse I usually increase the ratio slightly and cook it for 5min longer and let it sit covered for 5 additional minutes but the result will also be a much more stickier and starchy rice. People also for some reason stir rice which you should never do unless you are making glue or rice pudding (which tbh is the same recipe minus the sugar and flavorings).
- hantusk 6y agoAlso, don't add salt until the process is finished, as that also makes it more starchy
- gbear605 6y agoThe traditional method in a lot of Asia (per what I’ve read online) is to put a finger on top of the rice pointing down, so that your fingernail is touching the rice, and to fill water up to your knuckle.
- badfrog 6y agoThat's covered in the first video link
- yissp 6y agoWouldn't this result in different amounts of water depending on the dimensions of the pot?
- tzs 6y agoEvaporation rate should be proportional to surface area, so the volume of extra water you need to add to make up for that should also be proportional to the surface area too. Adding extra water to a fixed depth accomplishes that. This is assuming a pot with straight sides, at least above the lowest water level during cooking.
- wtvanhest 6y agoAh, I always wondered why that worked. I fought against it for a while, then started using that method out of laziness, but it works so well, I don’t use another method now.
- firethief 6y ago> Evaporation rate should be proportional to surface area, so the volume of extra water you need to add to make up for that should also be proportional to the surface area too. This would be accurate at room temperature, but under stovetop conditions wouldn't evaporation rate be determined mostly by the amount of heat energy added to the water?
- cma 6y agoAnd altitude.
- folknor 6y agoBoth, and more. In my experience, the surface area where evaporation occurs has the most impact. If I know (and obviously I do every time, just measure it) the evaporation area size, that's what I use to dial in how much pre-boil wort I need the first few times I use a set of equipment. But heat energy is the second most important factor. Sea level, salt/mineral levels, and other factors are - in my experience - not worth considering. But I've not tried to brew beer on the top of a mountain. I've brewed over 300 batches of beer in vessels of various dimensions (including surface area and evaporation area), and with various amounts of heat energy, applied in various places in the vessel. Ranging from 2kW to 18kW, sometimes heat applied under the pot, sometimes distributed throughout for example 3 heating elements at various heights. 2kW for all from 15L to 60L vessels, 6-18kW from 25L to 120L, and 18kW (IIRC) for 500-800L. When brewing beer, the boil usually lasts for 60-90 minutes, and the boil off rate is extremely important for hitting your target gravity and volume, and getting a consistent result if you're brewing the same recipe again. What you do as a brewer is you test the equipment on the first 2-3 batches and then after that you can hit your target boil-off with 99% accuracy every time, or 100% in an enterprise-grade professional setup. I've never been more than 5-10% off my estimated boil-off rate for the first batch, and I only account for surface area in that estimate. Even with 6kW for 25L.
- thiht 6y agoThat's not right. Jasmine rice for instance requires more like 1,5:1 water, at least (you can go up to 1,75 for extra softness). And for what it's worth, it's what is written on the bags I buy.
- throw0101a 6y ago> Jasmine rice for instance requires more like 1,5:1 water, at least (you can go up to 1,75 for extra softness). ATK mentions various types of rice that they experimented with; there doesn't seem to be anything special about jasmine: > We gathered 17 different varieties of rice, including white and brown short-grain, medium-grain, long-grain, basmati, and jasmine [!!!!] rice plus two varieties of red and black rice. After rinsing the rice to remove excess surface starch, we placed 1 cup of each type with 1 cup of water in a vacuum bag and sealed them to ensure that no water could evaporate during cooking. […] > To the surprise of our tasting panel, every variety of rice was properly cooked using the 1:1 ratio of rice to water. All of the rice types were tender throughout with no chalky or mushy grains. In addition, the water had been completely absorbed in each sample. * https://www.cooksillustrated.com/articles/1692-nailing-the-perfect-ratio-of-water-to-rice https://www.cooksillustrated.com/articles/1692-nailing-the-p... You can easily re-create their experiment: buy a bunch of rice, put them in sealed bags with water, completely seal the bags, and cook them sous vide. Cook one bag of jasmine at 1:1, one at 1.5:1, 1.75:1, etc. The statements are falsifiable / confirmable. Again: long/medium grain rice has 1.5:1 recommended, and brown rice 2:1, because of longer cooking times—which allows for more evaporation to occur. The rice itself only needs 1:1, anything else is about factoring evaporation which is fixed regards of quantity being cooked. So when measuring out: do 1:1 for the cups of rice, and then add the extra needed for your particular pot-stove combination.