5 ms·
Building a Reflow Oven
- unfoldedCravat 7y agoI've got a Zallus reflow controller off an old kickstarter - finally installed it this weekend into an old oven but haven't had a chance to try it properly. They seem quite a bit cheaper than the whizoo controller although it's much more limited. Mine doesn't control the door or heating elements independently. Apparently a popular use case for these is roasting your own coffee beans. http://www.zallus.com/ http://www.zallus.com/
- Stratoscope 7y agoThis is cool! I can buy a $30 Black & Decker toaster oven and turn it into a reflow oven. There are a few worrisome steps, like this section: > Ceramic fibers are very fine and sharp. They don't penetrate though thick skin, but can irritate thin tissue like eyes, nostrils and lungs. If you exercise precautions you won't have any problems. The blanket has amazing insulating properties, and the top of your oven will be barely warm during a reflow. > Things to keep in mind: • Unwrap the ceramic fiber blanket just before you use it - not earlier. • Clean up your workspace immediately after applying the blanket and closing the oven • If possible, wear a face mask (we recommend using N95 masks) • Wear shoes. Our preference is flip-flops that we can easily wash afterwards • Take care not to touch your eyes, lips or ears • Keep the area free of drinks, and use the restroom (toilet) before starting • Work in a draft-free environment. Don't use fans • Make slow movements to minimize dust • Make sure you have all your tools and parts close by (you need to close up the oven too) • Make sure pets, kids and neglected spouses don't come into your work area • Immediately after working with the blanket you should take a shower and wash your clothing > Scared? Don't be. Ceramic fiber is easy to work with as long as you take a few precautions. OK! I am not scared at all. I do have to wonder about the cost effectiveness, at least for myself. It sounds like a solid couple of days work to make this thing. Suppose I were looking for a ready-to-go reflow oven at some kind of reasonable price. Where would I start? Any recommendations?
- p1necone 7y agoSeems like it would be physically quite similar to asbestos. I wonder if it's comparable.
- tzs 7y ago> This is cool! I can buy a $30 Black & Decker toaster oven and turn it into a reflow oven $20 at Bed Bath & Beyond [1]. [1] https://www.bedbathandbeyond.com/store/product/black-decker-trade-4-slice-toaster-oven/1044115319 https://www.bedbathandbeyond.com/store/product/black-decker-...
- Stratoscope 7y agoMaybe $16 with one of my lifetime supply of 20% off coupons! This gives me an excuse to share the Three Secrets of Bed Bath & Beyond in-store coupons: 1. Even though the coupons have an expiration date printed on them, they do not expire. Keep your old ones and use them when you want. 2. You can use more than one coupon in a single visit. You can't stack them on one item, but if you have N coupons you can use them on N items. 3. If you forget to bring a coupon to the store, you can come back within 30 days with your receipt and a coupon and they will refund the discount amount. None of this applies to online purchases, only in-store.
- mindcrime 7y agoSuppose I were looking for a ready-to-go reflow oven at some kind of reasonable price. Where would I start? Any recommendations? Here's the rub... there are relatively inexpensive, COTS reflow ovens out there[1], and they do work - more or less. The problem is that many people find them to be more on the "less" side of that spectrum, without putting considerable work into upgrades and mods anyway. And once you take a cheap T962 off the shelf and start modding it, you might start to ask "why not just build my own from a toaster oven?" The toaster oven conversion winds up being cheaper, or - at worst - a wash, from a price standpoint. And many people find that they get better results from the converted ovens than they do from a T962. Unfortunately, the next "hop" up in quality in terms of commercial ovens winds up being a pretty big jump price wise. I haven't tried this myself yet, but I have a friend who has both a T962 and a conversion oven (made from a Black and Decker convection oven, so a little pricier than the model cited in TFA), and he only actually uses his converted oven. I trust his opinion a lot, so if/when I decide to get a reflow oven, I'm leaning hard towards doing this. [1]: https://www.amazon.com/Happybuy-Soldering-Machine-Infrared-Automatic/dp/B01LZYEF90/ref=asc_df_B01LZYEF90/?tag=hyprod-20&linkCode=df0&hvadid=312128028232&hvpos=1o1&hvnetw=g&hvrand=10004436235525553708&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9009670&hvtargid=pla-526334860728&psc=1 https://www.amazon.com/Happybuy-Soldering-Machine-Infrared-A...
- BrooklynRage 7y agoWhen I was a student, pretty much every student organization that did PCBs had one of these (FSAE Electric, Robotics clubs, etc.) This + boards from OSHPark or Advanced Circuits' 33/66 each deal were a great way to cheaply get started with PCB design.
- kurthr 7y agoHrrmmm... I like SMT. It's cheap, easy, and performs well. I haven't tried the ceramic paper, but I've only tried single sided reflow, and it worked fine without. I'd also worry a bit about fumes during reflow so doing it under a vent or hood (they recommend no drafts?) The challenge I saw was with silk screening the solder paste with the right alignment and thickness. Placement with tweezers and a binocular microscope (or young eyes) went fine once you do a couple. Post reflow rework substantially increased yield from ~80-90% to 99%. Make sure you have a test for those parts before you put then all together wrong!
- Animats 7y agoFinding a good reflow oven is frustrating. The Puhui T962 series units, available since 2014, were around $150, but they had wildly nonuniform temperature inside. I've had boards scorched at the center and failure to solder properly at the edges. There's an open source mod to those which makes them reasonably usable. New firmware that runs the cooling fan a bit during heating to distribute the hot air, and a proper cold end reference for the thermocouples.[1] With those mods, those things are usable. These things have been cloned in China; you'll see "T962" units that don't have a Puhui logo on Amazon and eBay. None of the cloners seem to have made these well-known improvements and delivered a good out of the box experience. The next step up costs much more. A nice little prototyping convection oven from Germany costs about $3500. There's not much in between the $200 units and the $2000 units. The article is really an ad for Whizoo's Controleo3 board, which is $249 with all the parts you need. So this isn't that great a deal. Most of the cheap solid-state relays on eBay and Amazon are fake. The current ratings on the unit are far beyond what the electronics inside can handle. Google "Counterfeit Fotek SSR" for details.[2] Since the failure modes are 1) fail in the ON state and 2) catch fire, this is not good for anything that draws significant current. The real ones are a lot more expensive than the fakes, and cost goes up with current rating. [1] https://hackaday.com/2014/11/27/improving-the-t-962-reflow-oven/ https://hackaday.com/2014/11/27/improving-the-t-962-reflow-o... [2] https://www.ul.com/node/81246 https://www.ul.com/node/81246
- CamperBob2 7y agohttps://www.estechnical.co.uk/ https://www.estechnical.co.uk/ has a very nice modification kit for the T962 that makes it quite usable, as well as controllable via USB. Unfortunately it's about as expensive as the oven itself, but the end result works very well and no longer torches boards.
- contingencies 7y agoPuhui T-962A @ $250 does the job if you don't want to DIY.
- ycui1986 7y agoI have both the Puhui T-962A and DIY conversion oven. The Puhui T962A will consistently burn your board. You solder joint will come out black as the temperature goes way beyond proper lead-free temp. You will never be able to solder any film capacitor. Any film cap you put into T962A will come out melted/exploded. It actually save your time to build you own oven then by the off-the-shelf T962.
- contingencies 7y agoWorks fine for us! Haven't had any issues to date, must have done over 100 different boards. There is third party firmware[0] for better control including an active fan if you run in to issues. Thanks for the tip though. [0] https://github.com/UnifiedEngineering/T-962-improvements https://github.com/UnifiedEngineering/T-962-improvements
- jwr 7y agoI would not follow the tip about connecting multiple thermocouples in parallel. The voltages involved are very small and the Maxim chips are very sensitive to noise. Source: myself, as I had to put in a diff 10nF capacitor between T+/T- of the 31855 to get good consistent readings. Maxim confirmed this is a known solution and they were supposed to put the recommendation in the datasheet. So, be careful with those thermocouples.
- kennywinker 7y agoI recently did a smd reflow using a cast iron pan and a few handfuls of sand. Worked like a charm. Got the idea here: https://hackaday.com/2014/02/15/smd-soldering-on-hot-sand/ https://hackaday.com/2014/02/15/smd-soldering-on-hot-sand/ Granted that was for fairly large, hearty components, but for many hobbyists it seems to me an oven is a bit overkill.
- bcaa7f3a8bbc 7y agoDoes your method work for QFN and DFN? I currently find them to be the biggest headache in prototyping. If you coat some solder on the chip and board using an iron and then reflow with a hot air station, it's easy to miss a few pins underneath due to uneven solder distribution; on the other hand, if you use solder paste and reflow with hot air, again, due to uneven solder distribution, you'll short some pins and miss others, and there is no straightforward way to fix it, the thing gets even worse when solder on the ground pad suddenly melts and causes unwanted movements (during rework) that misaligns the chip. I got my board working only by pure luck. I'd like to hear your recommendation.
- elcritch 7y agoQFN/DFN are pain, but I've had decent luck with them using the toaster oven method. Of course that's using a solder mask from JLC PCB, as without the mask you just end up with the incorrect amount of solder. Still you get the occasional missed pin you need to re-solder but it works.
- bcaa7f3a8bbc 7y ago> Still you get the occasional missed pin you need to re-solder but it works. How? Did you mean to remove all the existing solder, reapply the paste, and reflow again (can that even be done on an already populated board, where do you place the mask/stencil?), or it's something else?
- elcritch 7y ago
- matt_trentini 7y agoAn alternative controller is the Reflow Master by the Unexpected Maker: https://www.tindie.com/products/seonr/reflow-master/ https://www.tindie.com/products/seonr/reflow-master/ US$89 on Tindie (just add Toaster+SSR!) It's been used to reflow _thousands_ of boards including the majority of the TinyPICO's: https://www.crowdsupply.com/unexpected-maker/tinypico/ https://www.crowdsupply.com/unexpected-maker/tinypico/
- natvert 7y agoI also designed and built a reflow oven! My goal was to make it simpler / smaller: https://nathan.vertile.com/blog/2019/04/24/fluxlamp-the-soldering-reflow-over-for-hackers/ https://nathan.vertile.com/blog/2019/04/24/fluxlamp-the-sold... Email me if anyone wants control boards and I can try to make some more.
- thatcat 7y agoI like the light housing based design, pretty clever!
- 1asterisk 7y agoInstead of that nasty ceramic blanket and that reflective tape why not just use ceramic tile? Its cheap, easy to find locally, and will work better. True, it will be heavier, but it would be easier to maintain a consistent temperature. Another alternative would be the ceramic cement products like FiberFrax. It dries solid, so no floating fibers to be concerned with.