4 ms·

It might have been a SCSI drive/controller, but it might have also been that you used FastFileSystem, which was pretty efficient. One of the HD manufacturers o

by puzzle 8y ago

It might have been a SCSI drive/controller, but it might have also been that you used FastFileSystem, which was pretty efficient. One of the HD manufacturers of the time, either Conner or Maxtor, was known to use Amiga 3000 machines to test their SCSI disks, because of the CPU/chipset/OS/FS combination. Not many systems were able to extract 90%+ of theoretical throughput like the A3000 could.

zepearl 8y ago
Thx - it was just some sort of standard HDD for Amiga 500 - cannot remember anything specific about it... . Can it be that the Amiga 500 had in its case a place for a HDD? (I don't remember using external cases, but maybe I have forgotten...)
- puzzle 8y ago
  The A590 was a drive that plugged on the left side of the A500. It usually came with a 20MB SCSI disk inside... There was no room in the A500 for a 3.5" drive. Later, the A1200 and A600 had a built-in IDE controller and an internal bay, but for a 2.5" disk.
  - jacobush 8y ago
    The 590 had a SCSI controller with DMA, but only for the external SCSI connector. The internal drive was 8-but IDE and dog slow. So if it was faster, it must be chalked up to better OS, better filesystem and I would assume a 68000 at 7Mhz was faster than a 4.77Mhz 8088 at shuffling data around. Especially since the memory data bus was 16 bit wide for the Amiga but only 8 bit wide for the PC. (Right?!)
    - puzzle 8y ago
      The A590 had both a SCSI and an XT header for internal drives (on the right side): http://amiga.resource.cx/photos/photos/a590-5.jpg http://amiga.resource.cx/photos/photos/a590-5.jpg I only ever saw them with SCSI drives in person, but they also sold XT units. Maybe you saw the latter?
      - jacobush 8y ago
        If they sold'em with XT-IDE inside, I was probably unfortunate to have on of those. Still beat swapping floppies. Thanks to the HDD I could compile C programs without switching floppies all the time. IIRC I had the compiler and the headers on one floppy and the linker etc on another. Eventually I made DICE (Matt Dillon yo!) fit on one floppy. Or was it an early Lattice C?? Can't remember.:-P By that time I had bought a 486SX for uni, so I reluctantly used Turbo C instead. Turbo C was just too good to pass up...
  - zepearl 8y ago
    Yes, you're right - it was the A590, thx!
vidarh 8y ago
Part of it may also have been that even expansions that used non-SCSI drives tended to offload most of the processing from the CPU. My A2000 SCSI card had a Z80 on it, for example.

by puzzle 8y ago

zepearl 8y ago

Thx - it was just some sort of standard HDD for Amiga 500 - cannot remember anything specific about it... . Can it be that the Amiga 500 had in its case a place for a HDD? (I don't remember using external cases, but maybe I have forgotten...)

puzzle 8y ago
The A590 was a drive that plugged on the left side of the A500. It usually came with a 20MB SCSI disk inside... There was no room in the A500 for a 3.5" drive. Later, the A1200 and A600 had a built-in IDE controller and an internal bay, but for a 2.5" disk.
- jacobush 8y ago
  The 590 had a SCSI controller with DMA, but only for the external SCSI connector. The internal drive was 8-but IDE and dog slow. So if it was faster, it must be chalked up to better OS, better filesystem and I would assume a 68000 at 7Mhz was faster than a 4.77Mhz 8088 at shuffling data around. Especially since the memory data bus was 16 bit wide for the Amiga but only 8 bit wide for the PC. (Right?!)
  - puzzle 8y ago
    The A590 had both a SCSI and an XT header for internal drives (on the right side): http://amiga.resource.cx/photos/photos/a590-5.jpg http://amiga.resource.cx/photos/photos/a590-5.jpg I only ever saw them with SCSI drives in person, but they also sold XT units. Maybe you saw the latter?
    - jacobush 8y ago
      If they sold'em with XT-IDE inside, I was probably unfortunate to have on of those. Still beat swapping floppies. Thanks to the HDD I could compile C programs without switching floppies all the time. IIRC I had the compiler and the headers on one floppy and the linker etc on another. Eventually I made DICE (Matt Dillon yo!) fit on one floppy. Or was it an early Lattice C?? Can't remember.:-P By that time I had bought a 486SX for uni, so I reluctantly used Turbo C instead. Turbo C was just too good to pass up...
- zepearl 8y ago
  Yes, you're right - it was the A590, thx!

vidarh 8y ago

Part of it may also have been that even expansions that used non-SCSI drives tended to offload most of the processing from the CPU. My A2000 SCSI card had a Z80 on it, for example.