5 ms·

I would have just had the CO2 level read via a $8 I2C device connected to an Esp8266/Esp32 running Arduino. I would post the result to a web service in this fa

I would have just had the CO2 level read via a $8 I2C device connected to an Esp8266/Esp32 running Arduino. I would post the result to a web service in this fashion from the Esp8266: https://techtutorialsx.com/2016/07/21/esp8266-post-requests/ https://techtutorialsx.com/2016/07/21/esp8266-post-requests/ Then just setup a nice Graphana+Prometheus as a service, graphana.com is nice and can expose a Prometheus end point over basic http auth - easy to post to. Then you can setup alerts, graphs, dashboards, etc. In fact you could have a whole suite of IoT reports flowing in from various Arduinos really easily. Or at least a couple CO2 sensors spread around the house. Total investment of coding would be about 30-50 lines of Arduino code for the Esp8266 and you may even get away with the free plan on Graphana.com. I obviously like to outsource as much as possible these days. Less learning, but more efficient.

stackmad 8y ago
Totally true, but my soldering iron is in the basement, so ... ;)
Hobohodo 8y ago
Would you be able to share where you might get such a cheap CO2 sensor/the name of it? I've had trouble finding them for less than £60 in the UK and would like to set one up.
- RossM 8y ago
  Adafruit sell a 1-60,000 ppm equivalent-CO2 sensor for £15. https://www.adafruit.com/product/3709 https://www.adafruit.com/product/3709
  - aaaaaaaaaab 8y ago
    This doesn't measure CO2 levels. It measures volatile organic compounds and calculates the amount of CO2 that would cause the same greenhouse effect. >The SGP30 does have built in calibration capabilities, note that eCO2 is calculated based on H2 concentration, it is not a 'true' CO2 sensor for laboratory use.
    - janekm 8y ago
      Not even that. It is designed for hvac applications and measures VOCs on the assumption that they are from human breath and have a corresponding increase in CO2 levels due to breath.
- gsich 8y ago
  MH-Z14 or Z19 are cheap, but not 8$ cheap, more like 25.
- bhouston 8y ago
  I always check aliexpress.com https://www.aliexpress.com/wholesale?SearchText=co2+sensor+module https://www.aliexpress.com/wholesale?SearchText=co2+sensor+m...
- sbr464 8y ago
  https://www.co2meter.com/collections/sensors https://www.co2meter.com/collections/sensors has a bunch of different ones, I usually look on Mouser also. I don't have a name of one currently. I've been using the particle.io platform with a particle device/LTE for sending out data and programming them.
  - gsich 8y ago
    None of them are in the 8$ range. There also seem to some copies which are way overpriced.
    - sbr464 8y ago
      Interesting to have an arbitrary $8 price point. You only live once, get the best!
      - gsich 8y ago
        Not my restriction.
fulafel 8y ago
Slight aside, anyone know why all the supposedly iot-oriented small arduino devices are IPv4-only? Is everyone deploying them in some kind of NATs + port forwards / upnp system or tunneled overlay IPv4 network using external gateway devices?
- michaelbuckbee 8y ago
  Genuine question: are Arduino's really for IOT or for prototyping? Not an expert, just read a lot about startups starting with a RaspPI or Arduino prototype for the Kickstarter or something and then getting "real" dedicated hardware for production.
  - bhouston 8y ago
    Arduinos are not for production, but for prototyping, hobby projects.
  - PascLeRasc 8y ago
    It is common to start with these before the Kickstarter, just to get a proof of concept, but those boards (and the ESP8266) absolutely aren't for production. Raspberry Pis are terrible since the only way to interface with them is over a single USB 2.0 port - and that's shared with the 100M ethernet and the SD slot. You might see an ATMega328p chip isolated, and that's "good enough" for hobbyist projects where you just want to make HID easier on yourself. But I think most shops that need one of these three would be much better off with a STM32-series chip - they cost pennies compared to consumer boards, run on microamps, and have much better documentation. It'd be a huge red flag for me if I was interviewing with a hardware startup and they said they wanted to put Arduinos into mass production.
    - deleted 8y ago
      [deleted]
- ungzd 8y ago
  Seems that both "official" SDK for esp8266 and its Arduino port support ipv6 out of the box: https://github.com/esp8266/Arduino/pull/5136 https://github.com/esp8266/Arduino/pull/5136. esp8266-nonos-sdk/esp8266-rtos-sdk/esp8266-arduino uses lwip as tcp/ip stack, which supports ipv6.
gsich 8y ago
And where can you buy a 8$ Co2 sensor that doesn't suck?

stackmad 8y ago

Totally true, but my soldering iron is in the basement, so ... ;)

Hobohodo 8y ago

Would you be able to share where you might get such a cheap CO2 sensor/the name of it? I've had trouble finding them for less than £60 in the UK and would like to set one up.

RossM 8y ago
Adafruit sell a 1-60,000 ppm equivalent-CO2 sensor for £15. https://www.adafruit.com/product/3709 https://www.adafruit.com/product/3709
- aaaaaaaaaab 8y ago
  This doesn't measure CO2 levels. It measures volatile organic compounds and calculates the amount of CO2 that would cause the same greenhouse effect. >The SGP30 does have built in calibration capabilities, note that eCO2 is calculated based on H2 concentration, it is not a 'true' CO2 sensor for laboratory use.
  - janekm 8y ago
    Not even that. It is designed for hvac applications and measures VOCs on the assumption that they are from human breath and have a corresponding increase in CO2 levels due to breath.
gsich 8y ago
MH-Z14 or Z19 are cheap, but not 8$ cheap, more like 25.
bhouston 8y ago
I always check aliexpress.com https://www.aliexpress.com/wholesale?SearchText=co2+sensor+module https://www.aliexpress.com/wholesale?SearchText=co2+sensor+m...
sbr464 8y ago
https://www.co2meter.com/collections/sensors https://www.co2meter.com/collections/sensors has a bunch of different ones, I usually look on Mouser also. I don't have a name of one currently. I've been using the particle.io platform with a particle device/LTE for sending out data and programming them.
- gsich 8y ago
  None of them are in the 8$ range. There also seem to some copies which are way overpriced.
  - sbr464 8y ago
    Interesting to have an arbitrary $8 price point. You only live once, get the best!
    - gsich 8y ago
      Not my restriction.

fulafel 8y ago

Slight aside, anyone know why all the supposedly iot-oriented small arduino devices are IPv4-only? Is everyone deploying them in some kind of NATs + port forwards / upnp system or tunneled overlay IPv4 network using external gateway devices?

michaelbuckbee 8y ago
Genuine question: are Arduino's really for IOT or for prototyping? Not an expert, just read a lot about startups starting with a RaspPI or Arduino prototype for the Kickstarter or something and then getting "real" dedicated hardware for production.
- bhouston 8y ago
  Arduinos are not for production, but for prototyping, hobby projects.
- PascLeRasc 8y ago
  It is common to start with these before the Kickstarter, just to get a proof of concept, but those boards (and the ESP8266) absolutely aren't for production. Raspberry Pis are terrible since the only way to interface with them is over a single USB 2.0 port - and that's shared with the 100M ethernet and the SD slot. You might see an ATMega328p chip isolated, and that's "good enough" for hobbyist projects where you just want to make HID easier on yourself. But I think most shops that need one of these three would be much better off with a STM32-series chip - they cost pennies compared to consumer boards, run on microamps, and have much better documentation. It'd be a huge red flag for me if I was interviewing with a hardware startup and they said they wanted to put Arduinos into mass production.
  - deleted 8y ago
    [deleted]
ungzd 8y ago
Seems that both "official" SDK for esp8266 and its Arduino port support ipv6 out of the box: https://github.com/esp8266/Arduino/pull/5136 https://github.com/esp8266/Arduino/pull/5136. esp8266-nonos-sdk/esp8266-rtos-sdk/esp8266-arduino uses lwip as tcp/ip stack, which supports ipv6.

gsich 8y ago

And where can you buy a 8$ Co2 sensor that doesn't suck?