6 ms·
Fully digital valves open up engine possibilities
- rmason 8y agoIt seems in tech just when the incumbents seem like they will lose to the upstart they achieve a breakthrough and the inevitable is delayed for a few more years. Combine this breakthrough with what Michigan State is doing in gas powered engines and battery powered cars dominance is delayed for at least another decade. http://www.wkar.org/post/reworking-michigan-msu-develops-light-weight-high-efficiency-engine#stream/0 http://www.wkar.org/post/reworking-michigan-msu-develops-lig...
- derekp7 8y agoI would think that could help EVs, as it would be cheaper (in weight and dollars) to add a gas powered range extender to EVs with smaller batteries. I'd rather have an 80 mile EV with a range extender than a very expensive heavy 400 mile EV.
- TylerE 8y agoThat’s probably one of the least interesting applications, really. We’re already quite good at optimizing engines for a narrow RPM/power range.
- derekp7 8y agoI was thinking more of optimizing for weight. Also, if you optimize for narrow RPM, then you are only using the gas engine to power a generator, so you have some loss there. I'd rather have the gas engine power i.e., the front wheels, while the EV powers the rear wheels (or vice versa).
- mkstowegnv 8y agoThe inherently self destructive nature of ICE's make it likely that ICE vehicles will always be more complex, less reliable/ higher maintenance than comparable all electric vehicles. The simplicity advantage of electric will soon take a quantum leap when driveshaft-free 4 motor all wheel drive vehicles hit the market [1]. On the other hand as long as batteries are heavy, ICE's will have a place in aircraft, and I would think the OP's technology could be huge for helicopters. 1 http://www.electric-vehiclenews.com/2017/06/hondas-all-electric-nsx-4-motor-ev-is.html http://www.electric-vehiclenews.com/2017/06/hondas-all-elect...
- ak217 8y ago> The simplicity advantage of electric will soon take a quantum leap when driveshaft-free 4 motor all wheel drive vehicles hit the market You can't just eliminate the driveshaft because the wheel must be on a suspension. Remove the driveshaft and you have to put the motor on the wheel, increasing unsprung weight, exposing the motor and making high voltage parts subject to damage. 4 motors is more complex than 2 and doesn't buy you much except in niche packaging applications (like buses). As far as torque vectoring, you can achieve the same effect with differential braking (the duty cycle of torque vectoring is very short, so you don't lose any efficiency). A 2-motor Tesla is probably already the optimal passenger car configuration. Agreed on everything else though.
- hevi_jos 8y ago4 electric motors on wheels is extremely simpler than 2 motors, mechanical differentials and couplings. I actually helped a mechanical engineer to create a simulator for car dynamics in software. Today's cars are over engineered mechanically in order to support and resist the forces and torques from the motor to the wheels. When you put the motors in wheel you basically reduce the required rigidity and the weight of the car substantially. You point out some disadvantage of the approach. The biggest disadvantage of all is that is not a proven technology, like 100 years old driveshaft. That means the company that commercializes it will eat all the risk, like what happens when people exposes the motor-wheels to wet surfaces and some part of it is damaged. The lawsuits could bankrupt even the biggest company.
- ak217 8y agoI agree with you. I should have clarified - 4 motors in the arrangement envisioned by Honda (see the link above) is more complex than 2. It doesn't eliminate any of the driveshafts. I don't think we'll see in-wheel motors any time soon for the reasons you and I mentioned. (Also, in high performance applications (anything but econoboxes) won't you need to strengthen the suspension/chassis in some places even as you get to lighten it in others, since the motor is now torquing the rest of your suspension?)
- 8y ago
- deleted 8y ago[deleted]
- ak217 8y agoI wouldn't put either free valves or the "wave disk" engine on the list of technologies likely to affect mass produced ICE efficiency in the next decade or two. HCCI/SCCI gas engines with VVT, variable displacement, and cylinder deactivation are very close to full scale production though, and promise very substantial improvements. Mild hybrid (electric regenerative braking and assist with a small battery/large capacitor) gives another boost, though at a substantial complexity cost (not nearly as bad as a full hybrid though).
- inferiorhuman 8y agoWell this quote from the original article struck me as odd: > Nobody's ever done variable valve timing on the exhausts, so the benefits are less well understood. BMW's been doing this for twenty years. Honda's been at it for over thirty years. On. The. Exhaust. Valves.
- rasz 8y agotoyota 1998 Dual VVT
- tomatotomato37 8y agoI thought koenigsegg was already doing this with their freevalve thing Also I saw an interesting point in an article about the koenigsegg thing that would pertain to this too; environmental laws would be much harder to practically enforce with this as you could run virtually any engine anemic enough to get though the emissions tests (and set it as the default mode to get around the Volkswagen nonsense) and then offer high/sport/cruise modes that runs the engine at full capacity otherwise
- thinkingkong 8y agoWouldnt the test just need to apply to all modes? If its a matter of automatically tuning through a series of conditions then its reasonable that those could be documented and tested by the facility / standards body.
- yontherubicon 8y agoSure, but emissions testing after you've got the car would be utterly useless.
- inferiorhuman 8y agoHow so? Roadside emissions testing is very much a thing, as are annual emissions checks.
- HeyLaughingBoy 8y agoNot in all states. I haven't had to do it in 20 years.
- londons_explore 8y agoThe solution to this is to mandate that the car have built in emissions modelling. The car itself must keep track of how much Nox it has produced and how many miles it's driven. The ratio must stay below some legal limit (or you pay an extra pollution tax to go over it)
- westmeal 8y agoCan private citizens obtain these?
- maxxxxx 8y agoWhen I did my mechanical engineering degree a long time ago this would have been the holy grail for engines. Let's hope reality doesn't offer drawbacks to this system like it happens to so many other engine designs.
- jondumbau 8y agoThe temporary 2 stroke idea doesn't sound very well cooked. Fine control over the valves is great, but the exhaust and other aspects of the engine need to be tuned for that use case.
- jondumbau 8y agoAlso the "2 strokes are the future" remark seems a bit off too. The future of enduro bikes and chainsaws maybe.
- Fjolsvith 8y agoYeah, this idea is just in time for the all-electric revolution.
- King-Aaron 8y agoThe "all-electric' revolution you've got in mind is likely much further away than you expect. There will be a market for internal combustion engines for many more decades before all-electric vehicles can replace the markets in areas that are more remote, or require long hauling vehicles etc.
- jondumbau 8y agoagree. but you can barely get a 2 stroke passed the existing emission laws, and they're not generally in use in motor racing outside of enduro. ¯\(°_o)/¯
- londons_explore 8y agoYes, but like the hard drive market, as soon as a replacement technology comes over the horizon, all investment in improvements to the existing tech pretty much stops.
- jondumbau 8y agoNitpicky, but compression release for easy (easier..) starting is already a thing. It talks about completely opening the valves so the starter only overcomes friction. Presumably they're talking about having the cylinders that aren't yet fired spinning over freely? Otherwise it's a very efficient way to spin and engine that can't possibly start without "compressing gasses".
- TheSpiceIsLife 8y agoExhaust valves are open during the exhaust stroke anyway. Inlet valves are open during the intake stroke anyway. The strongest plausible interpretation of what¹ they're saying is to open valves that are partway through the compression stroke, and open / close any other valves as necessary at the best possible time to promote rapid starting. 1. https://news.ycombinator.com/newsguidelines.html https://news.ycombinator.com/newsguidelines.html
- jondumbau 8y agothat really makes the most sense. at that point i imagine it would be a more finely controlled compression release. i shouldn't read too much into the wording of what is essentially a marketing statement i suppose :)
- taneq 8y agoI guess it'd lower the starting torque which might let them use a smaller starter motor? You'd spin the engine for a couple of revolutions, then use the stored kinetic energy to kick start the engine.
- ebikelaw 8y agoThis article is pretty much wall-to-wall snake oil. The bit at the end is just completely false. Some people, who hadn't really bothered to do the math at the time, believed fifty years ago that spring-closed valves would float at high speeds and desmodromic valves were the solution. But that isn't true: metallurgy marches on, and nobody has been seriously impeded in making an engine turn at any desired speed with valve springs. Motorcycle engines turn at stupefying speeds without experiencing valve float. In practice it's actually the desmodromic designs that are troublesome, because of all that moving mass. Anyway, there are lots of other dumb claims in here, like nobody has ever done variable timing of exhaust valves, which is obviously not true.
- jaclaz 8y ago>Motorcycle engines turn at stupefying speeds without experiencing valve float. In practice it's actually the desmodromic designs that are troublesome, because of all that moving mass. Sure, go tell Ducati.
- ebikelaw 8y agoTell them what? That literally every other major manufacturer makes a motor with higher max engine speeds, higher reliability, and lower maintenance costs? Or that in the 60-year history of Grand Prix motorcycle racing they've only won once?
- Animats 8y agoThe idea has been around for a long time. Most of the big auto companies have played around with it. There are at least four startups in this space. The big problem is a good actuator, not compute power. Here's an actuator demo from 2014.[1] It can be made to work, but so far, it's not cost-effective. Maybe this time. [1] https://www.youtube.com/watch?v=ZYEjAv0hFug https://www.youtube.com/watch?v=ZYEjAv0hFug
- kwhitefoot 8y agoYou don't necessarily need such valves to make engines easier to start. I remember my father-in-law's Lister diesel generator, from over forty years ago, that would start automatically when you turned on a light or appliance. It had a tiny starter motor and also a starting handle in case the battery was flat. There was a switch or valve that you would turn manually, or if the battery was not flat automatically, that made it possible to turn the motor. It was pretty much impossible to turn the engine over manually without doing that; with it, it was easy. I'm not a mechanical engineer and I have no idea how it worked beyond knowing that it reduced the degree of compression.
- parimm 8y agoIts called a decompression valve.
- parimm 8y agoThey have replaced a pure mechanical linkage with a motor in each valve. A typical 4 cylinder engine will now need sixteen extra motors to run it. While I like the idea of controlling the timing of each valve interdependently for the other, I am not for the additional electronics in the engine.
- rasz 8y agoIts even worse, they replaced 1 camshaft with 4 camshafts, because electric linear actuators are not there yet (and probably never will be).
- huffmsa 8y agoThis means you can actually have a push-button anti-lag system. Push once for normal, nice keep the home owners association happy mode. Push twice for Group B hell on Earth mode.
- dreamcompiler 8y agoI wish cars had had this 50 years ago. Camshafts are a terrible way to control an IC engine. But it's too late now. Ironically, the same advances in power electronics, cheap high-speed computers, and electromechanical actuation that made individual valve control possible also enabled efficient electric drive motors that made valves in cars a non-problem.