4 ms·
Sigh. I've coded too much this week. My brain just immediately went to: comment out half the city at a time and binary search the source. Guess you can't really
by Waterluvian 9y ago
Sigh. I've coded too much this week. My brain just immediately went to: comment out half the city at a time and binary search the source. Guess you can't really do that.
I wonder if the hum persists during a power outage.
- deleted 9y ago[deleted]
- thinkingemote 9y agoI've heard the hum in a city in the UK quite frequently. I hear it more on monday bank holiday mornings, oddly. So a weekday but less people at work. I actually think it's the sound of traffic.
- vlasev 9y agoReplace "comment out" by "turn off the electricity for" and maybe we can binary search it.
- deleted 9y ago[deleted]
- asaph 9y agoYour implicit assumption is that the hum is caused by something electrical; i.e. not a diesel engine or some natural cause.
- Untit1ed 9y agoThen we can turn off the electricity for the whole town and see if it stops! :D
- incompatible 9y ago"The University of Windsor report said the hum’s likely source was blast furnace operations on Zug Island" ... which is over the border in the United States. Cutting off the power to that island would be a good thing to try, but apparently the US is uncooperative.
- Waterluvian 9y agoBut that's exactly the point. It would rule out a ton of stuff.
- manojlds 9y agoBut might have to turn off electricity for days if generators are used.
- demircancelebi 9y agoThis actually sounds like a good idea.
- koolba 9y agoA few samples of amplitude should be able to triangulate it no?
- rocqua 9y agoI'd guess amplitude is massively affected by microphone sensitivity. This is not easy to measure and might depend on the direction. Consider: * The amount of walls between a mic and the outside. * The absorbance/reflection of nearby materials, including their shape (flat surface will reflect sounds amplifying certain directions). * The clutter between the source and receiver. Sound carries over water, not over cities or forests. * Similarly, elevation of the receiver. Higher means less effect of clutter, and obviously, a hill in between will be an issue. * Wind direction. Wind will blow the sound away. It might still work with enough measurements with the same microphone, but that is not a given. A decent backup plan would be measuring the phase difference. This is still frustrated by wind, but doesn't depend on the senstivity of the microphones. It does require synchronization of the recordings, which might also be difficult.
- mindcrime 9y agoIt does require synchronization of the recordings, which might also be difficult. Could you record with a multiple "microphone connected to a Raspberry Pi" setup, with the time synchronized using something like the NIST time signal[1] using an RTL-SDR, or a cellular signal, or GPS, or maybe using NTP? [1]: https://www.nist.gov/pml/time-and-frequency-division/nist-radio-broadcasts-frequently-asked-questions-faq https://www.nist.gov/pml/time-and-frequency-division/nist-ra...
- rocqua 9y agoYes, that seems like the best approach. At 20Hz waves, ntp would probably be good enough. The real issue I can see is to get that time-data into the sound data. Maybe you could time-stamp the beginning of a recording, and start a new recording every minute (to compensate clock drift). That might work, biggest issue I see is potential variable latency between 'starting a recording' and the actual first recording happening.
- bufferoverflow 9y agoJust install the debugging microphones all over, collect the data, find the source (if it's real).
- sneak 9y agoWhy install anything? Fly a drone around to take 5s recordings at points on a grid.
- Cerium 9y agoSince cities support parallel execution you must have an array to capture coherent debug information.
- monk_e_boy 9y agoWouldn't the sound of the drone be louder than the hum?
- tntniceman 9y agoMy assumption is that he would touch down first.
- fredsmith42 9y agoI don't think that Windsor was compiled with the debug flags turned on.