3 ms·
>> around the same volume as an Olympic swimming pool. >> with each 400-megawatt unit capable of warming 200,000 urban households. >> with temperatures not ex
by sandworm101 9y ago
>> around the same volume as an Olympic swimming pool.
>> with each 400-megawatt unit capable of warming 200,000 urban households.
>> with temperatures not exceeding 100 degrees Celsius,
Think about that for a minute. If the water isn't going to exceed 100c but the reactor is still going to pump out 400-megawatts, it isn't going to be a calm pool. They are going to have to pump insane amounts of water in and out of this pool if they want to keep things under 100c. That's fine. Just don't pretend this is going to hum along quietly like a research reactor. And don't tell me thing will remain at 100c should that flow of water be interrupted. Any non-boiling, low-pressure, reactor is going to need exponentially more cooling (by volume) than an equivalent traditional reactor. Let us hope they keep a lake nearby as backup.
- adrianN 9y agoIt is possible to regulate the output of a nuclear reactor. In case the pool boils off in some freak accident, the chain reaction also stops, because water is acting as a neutron moderator in these designs. So you only have to ensure that the residual heat from normal decay doesn't melt the reactor. That doesn't sound too hard.
- Symmetry 9y agoIsn't the residual heat from normal decay something like 10% of the reactor output? When you split Uranium you get a lot of byproducts with short half-lives that continue decaying away even when Uranium chain reaction stops. So you've still got 40 MW to deal with, at least until those short-half-lived byproducts finish decaying.
- adrianN 9y ago5% for the first few seconds: http://www.euronuclear.org/info/encyclopedia/r/residual-heat.htm http://www.euronuclear.org/info/encyclopedia/r/residual-heat... but your point of course still stands. It's certainly not trivial to build passive-safe reactors, but it's also not impossible.
- vilhelm_s 9y agoAccording to one document[1] > The decay heat produced by a reactor shutdown from full power is initially equivalent to about 5 to 6% of the thermal rating of the reactor. This decay heat generation rate diminishes to less than 1% approximately one hour after shutdown. However, even at these low levels, the amount of heat generated requires the continued removal of heat for an appreciable time after shutdown. At 400 MW it takes about 4 hours to boil the water in an olympic swimming pool[1], so there should be some safety margin for the power to drop. Then once it is down to 1% decay heat it could boil for a couple of weeks before running dry. [1] https://web.archive.org/web/20110316042315/http://www.hss.doe.gov/nuclearsafety/ns/techstds/standard/hdbk1019/h1019v2.pdf https://web.archive.org/web/20110316042315/http://www.hss.do... [2] http://www.wolframalpha.com/input/?i=(specific+heat+of+vaporization+of+water)+*+(2500+m%5E3)+*+(density+of+water)+%2F+400+MW http://www.wolframalpha.com/input/?i=(specific+heat+of+vapor...
- sandworm101 9y ago>> you only have to ensure that the residual heat from normal decay doesn't melt the reactor. Not hard if this is a passive-cooling design. My point is that at these power levels passive cooling isn't enough. Stop the pumps and the reactor may build up enough heat to start melting things very quickly, long before the pool boils dry.
- nabla9 9y agoCorrect me if I'm wrong but isn't the idea of safe pool reactors that hydrogen-neutron heat transfer is more efficient than normal radioisotope-water heat transfer. If you shut down the pumps and heat increases, spectral hardening cools the reactor faster and disperses the energy into larger volume than convection using pumps.
- vilhelm_s 9y agoIs that really true? My understanding is that ordinary boiling water reactors contain safety systems that work just by boiling. Reading the wikipedia article[1], the Isolation Condenser, the Automatic Depressurization System, and the Gravity-driven Cooling System all work just by water boiling and with natural convection in the water, without any active pumps, and they are supposedly enough to keep the core from melting. [1] https://en.wikipedia.org/wiki/Boiling_water_reactor_safety_systems https://en.wikipedia.org/wiki/Boiling_water_reactor_safety_s...
- sdfasfdsaf 9y agoNo reactor is a calm place. The heat capacity of water changes with pressure, but not by orders of magnitude. So any 400 MW reactor has to pump similar amount of water to keep the T constant. So the pumps have to be similarly sized, except you no longer need a pressure vessel.
- CompelTechnic 9y agousing a specific heat of 4184 J/ kg*°C, those 400 megawatts can heat 1200 kilograms of water from 20°C to 100°C every second. That's a lot of hot water. You would need a 1 meter diameter pipe flowing at 1.5 meters/sec to supply this.