3 ms·

>The last link you posted seems to imply it will talk to a solenoid (NC or NO) only - would be very curious how that goes. The way CR02 wiring works is that yo

>The last link you posted seems to imply it will talk to a solenoid (NC or NO) only - would be very curious how that goes. The way CR02 wiring works is that you have a common ground and then you feed the 12V to one of two wires. The valve takes care of stopping the motor when fully open and fully closed so it should minimize power consumption. So my plan is take that normal NC/NO relay and feed the 12V to the common wire and wire NC and NO to each of the two valve wires. Since the programmable relay itself is also powered by 12V I get away with a single power source. My hope is a simple pack of low self-discharge 8xAA NiMH or similar will last a season. But a 12V lead battery and a solar panel could work as well. Aliexpress has a very big selection of different kinds of actuated ball valves. If they actually work reliably it seems like a great solution as it's a normal valve operated by a motor. See this for example for a selection of voltages and the 5 wiring types: https://www.aliexpress.com/item/CWX-25S-mini-electric-actuator-control-ball-valve-with-manual-override-function-DN8-DN10-DN15-DN20/32812620201.html https://www.aliexpress.com/item/CWX-25S-mini-electric-actuat... That one I linked was picked quite carefully to be stainless steel and CR02 wiring which seems to be the easiest to operate with just a single relay. I've received the relay but not the valve yet so I haven't tested everything yet. >I have several dozen old water timers with the o-ring seal ... where the o-ring seal has failed, and the insides rusted out. I now cover them all in thick plastic bags, and keep them under pit covers / galv steel lean-tos. Probably explains why they tend to last more than one Australian summer, too. Those are some rough conditions if the o-ring failing is enough to rust everything. I'd expect the threading itself to provide quite a bit of protection already. Can't imagine how you'd get much moisture through all those threads. One thing I have noticed is that you shouldn't torque the lid hard so as to not deform the o-ring too much.

pedrocr 9y ago
UPDATE: finally got the valve and it works fine with the controller. The combo uses 8mA when closed, ~80mA while opening (for ~5secs) and ~40mA while open (half is the relay in the controller half is the valve). This makes it outside the range of a simple battery but should work fine if you have a solar setup with a 12V battery or an AC mains and a simple 12V power source. So far I'm happy with the domestic all-in-one I linked so I'll probably not pursue this more. If a simple NiMH pack worked I'd probably trial a full setup. But if I was going further I'd use a DIN 12V programmable relay like this: https://www.aliexpress.com/item/New-DIN-Rail-Time-Relay-Switch-Digital-LCD-Power-Programmable-Timer-DC-12V/32785835109.html https://www.aliexpress.com/item/New-DIN-Rail-Time-Relay-Swit... and a DIN 12V power source like this: https://www.aliexpress.com/item/DR-15-12-Hot-sales-China-mainland-15w-12v-Din-Rail-power-supply-single-output/32702839079.html https://www.aliexpress.com/item/DR-15-12-Hot-sales-China-mai... all enclosed in an outdoor distribution box like this: https://www.aliexpress.com/item/Free-Shipping-IP66-Waterproof-Outdoor-Distribution-Box-4-Way-Air-Swith-Box-High-voltage-Electrical-Box/32515199355.html https://www.aliexpress.com/item/Free-Shipping-IP66-Waterproo... That way everything gets properly packaged using DIN elements. If you have a 12V panel/battery you don't need the AC->12V power source of course.

pedrocr 9y ago

UPDATE: finally got the valve and it works fine with the controller. The combo uses 8mA when closed, ~80mA while opening (for ~5secs) and ~40mA while open (half is the relay in the controller half is the valve). This makes it outside the range of a simple battery but should work fine if you have a solar setup with a 12V battery or an AC mains and a simple 12V power source. So far I'm happy with the domestic all-in-one I linked so I'll probably not pursue this more. If a simple NiMH pack worked I'd probably trial a full setup. But if I was going further I'd use a DIN 12V programmable relay like this: https://www.aliexpress.com/item/New-DIN-Rail-Time-Relay-Switch-Digital-LCD-Power-Programmable-Timer-DC-12V/32785835109.html https://www.aliexpress.com/item/New-DIN-Rail-Time-Relay-Swit... and a DIN 12V power source like this: https://www.aliexpress.com/item/DR-15-12-Hot-sales-China-mainland-15w-12v-Din-Rail-power-supply-single-output/32702839079.html https://www.aliexpress.com/item/DR-15-12-Hot-sales-China-mai... all enclosed in an outdoor distribution box like this: https://www.aliexpress.com/item/Free-Shipping-IP66-Waterproof-Outdoor-Distribution-Box-4-Way-Air-Swith-Box-High-voltage-Electrical-Box/32515199355.html https://www.aliexpress.com/item/Free-Shipping-IP66-Waterproo... That way everything gets properly packaged using DIN elements. If you have a 12V panel/battery you don't need the AC->12V power source of course.