3 ms·
And how much RAM does that FPGA hold? When your entire chip is programmable-logic, you don't have much room for RAM. The MachXo3LF-6900 has a grand total of 24
by dragontamer 10y ago
And how much RAM does that FPGA hold?
When your entire chip is programmable-logic, you don't have much room for RAM. The MachXo3LF-6900 has a grand total of 240 kBITs, or 30kBytes of storage.
In contrast, the STM32F746G will get you 320kBYTES of storage, 10x the capacity.
At 75MHz and 1-bit per cycle, that's still only 35ms of storage. Furthermore, it'd be a lot easier to program a Microcontroller to compress the data as its reading it, rather than use the FPGA.
The Microcontroller will still get you the Ethernet and USB connections too.
--------
I think this is a job for a microcontroller, not an FPGA. FPGAs are nice and flexible of course, but Microcontrollers offer you far more performance if you're going to use the specific features.
The STM32F746G has GPIO -> DMA directly to its RAM, while the CPU can compress 1/2 of the signal and send it out while the GPIO pins are simultaneously working. That's... pretty good. I have doubts that a cheap FPGA can accomplish all that at the same speed.
- vvanders 10y ago> I have doubts that a cheap FPGA can accomplish all that at the same speed. A cheap FPGA can probably do that at 5x the speed. Parallel operations like these are specifically what they're build for.
- dragontamer 10y agoSpeed isn't the only consideration here. 5x the speed needs 5x the RAM to store it in. But FPGAs will NEVER have as much RAM as a dedicated microcontroller. Again, you're looking at ~320kBytes on the $25 STM32 microcontroller board, against ~30kBytes on the $25 FPGA board. With 1/10th the RAM, the FPGA will store far less useful data. The typical Oscilloscope is like 100MHz. Getting a cheap 75MHz logic analyzer is perfectly acceptable. Storing and processing all that data (ie: outputting it to an Ethernet port) start to become the main issues once the speed issue is solved. In my experience, those small FPGAs run out of room rather quickly too. Throw down something as simple as a Wallace tree multiplier and suddenly half your LUTs are eaten up.
- revelation 10y agoWhat are you even talking about? FPGAs routinely interface with DDR3 and other "big buckets of memory" should you need them. Try that with your STM32.
- dragontamer 10y agoWhat price point are we talking about here? Throw down a single DDR3 Memory chip, and you've already eaten up like half the $25 hardware budget. http://www.digikey.com/product-detail/en/micron-technology-inc/MT41K512M8DA-107-AIT-P/557-1762-ND/6036290 http://www.digikey.com/product-detail/en/micron-technology-i... The "embedded" solution is: buy embedded on-board SRAM when you need it, and if necessary, buy an embedded on-board SRAM memory controller if you need it. Building your own memory-controller out of an FPGA sounds like hell to layout. Anyway, if we're talking about cheap stuff, DDR3L isn't the technology of note. This is about simpler SDRAM-level stuff, maybe a few MB at a time is sufficient. ---- Furthermore: How many LUTs will your memory controller take up? http://www.latticesemi.com/en/Products/DesignSoftwareAndIP/IntellectualProperty/IPCore/IPCores01/DDR3SDRAMController.aspx#_D5983CCD053543DA9E0D5AC1F76E34D4 http://www.latticesemi.com/en/Products/DesignSoftwareAndIP/I... According to this, Lattice's DDR3L 16-bit memory controller is 2500 LUTs. The $25 FPGA only has 6300-LUTs, so you've already used up 40% of the chip on just memory-interfacing! Yeah, you can accomplish a lot with a $600 FPGA with a Million-bajillion-LUTs and embedded cores. But at the $25 price point, FPGAs often run out of room. You don't have many LUTs to work with. Dollar-for-dollar, a microcontroller will outperform an FPGA in most tasks. That's just the facts. ASIC-implemented memory-controllers and ASIC-implemented large banks of internal SRAM just work better for computer-like tasks. FPGAs should be used for custom logic that isn't typically handled by a microcontroller / microprocessor. Not memory-controllers and ALUs that already exist in an easily packaged form. There's a reason why high-level FPGAs have embedded ARM cores and embedded memory-controllers in them (alas: such technology is likely out of the reach of cheap $25 FPGAs)
- zokier 10y agoHere is just a random FPGA board with onboard 32MB SDRAM. All with whopping $17 BOM according to the author: > Earlier this year, I calculated the part cost of the CAT Board with an HX8K at $17 https://hackaday.io/project/7982-cat-board https://hackaday.io/project/7982-cat-board
- anfractuosity 10y agoHave a look at the Saleae logic analysers for example, they combine an FPGA with an EZ-USB FX3, in the case of the Logic Pro 8. http://www.eevblog.com/forum/testgear/saleae-logic-pro-8-quick-teardown/ http://www.eevblog.com/forum/testgear/saleae-logic-pro-8-qui... I believe the FPGA is often being used for converting fewer high speed inputs, to a greater number of lower speed outputs for the GPIO of the FX3, I think that's called SerDes (please correct me if I'm using that phrase incorrectly).