4 ms·
Guitar d00ds having obscure, nonsensical reasons for things because "mah tones!"? Say it ain't so. I mean, nearly every tube head on the market has an essenti
by busterarm 10y ago
Guitar d00ds having obscure, nonsensical reasons for things because "mah tones!"? Say it ain't so.
I mean, nearly every tube head on the market has an essentially pointless standby/bypass switch because of the mistaken belief that you need to warm up your tubes for some arbitrary amount of time in a modern amp and keep them warm.
I forget which manufacturer it was that dropped the switch on one model and saw sales plummet and got freaked out support calls asking why the switch wasn't there. Next iteration had the switch back.
- failrate 10y agoIf I ever made analog audio equipment professionally, I would add an entire series of switches and dials that weren't wired up to anything.
- jandrese 10y agoYou could label them like "warmth", "aggressiveness", "heart", and have people go apeshit trying to figure out the best setting for their song.
- PeanutNore 10y ago"Girth"
- failrate 10y agoZest, Ennui, Anticipation
- zimpenfish 10y agoFrobulator on iOS has "orbit", "vexity", "doubt".
- WalterBright 10y agoBack in the 70's, a friend of mine created a formula where the inputs were number of switches, number of dials, and number of meters and would output the price. It was remarkably close at predicting the price of most any stereo receiver/amplifier in the stereo store. One standout anomaly was the Heathkit 250W amp, which just had an on/off switch and 2 meters.
- pravda 10y agoJust make sure the dials go up to eleven! For that one more, that extra push over the cliff. https://www.youtube.com/watch?v=KOO5S4vxi0o https://www.youtube.com/watch?v=KOO5S4vxi0o
- tnecniv 10y agoEddie Van Halen did precisely that to his guitar.
- mdb333 10y agoI wouldn't say they're pointless but more of a convenience than a necessity in most modern designs. Probably more important in vintage amps with old tubes and such where folks generally want to be more gentle and preserve the life of the tubes. Either way depends on the amp & circuit and you're right in many cases aren't needed.
- PeanutNore 10y agoI never include a standby switch if I build a tube head from scratch, but when I build out of a "donor amp"* that has one I keep it, because it's at least useful as a mute switch. *Using a cheap tube amp from CL as the basis for a new build and tossing everything except the chassis and transformers, and maybe the sockets if they are chassis mounted, is a great way to build a great sounding tube amp on the cheap.
- mveety 10y agoWell tube amps do actually need to warm up, but people think it takes minutes to hours for them to warm up when it really takes like 2 to 5 seconds. That, I think, comes from a lack of knowledge about how tubes work and the general cargo cult surrounding sound electronics.
- etatoby 10y ago"Cargo cult" summarizes that attitude well.
- PeanutNore 10y agoThey usually specify a warm-up time on the datasheet. For most 12A_7 preamp tubes it's 11 seconds
- fuzzfactor 10y agoNon-solid-state electron systems should be expected to have their own idiosyncracies, regardless of whether superstition is building up faster than it is being dissipated. The regular ordinary procedure for cold-starting high-power vacuum tube systems is to switch on the unit while the tubes are in standby. This will allow the cathodes to heat to their characteristic glow, fully developing the ability to deliver the current you will soon be demanding. But no high voltage is applied to the anodes (there will be no sound from audio systems) until removed from standby. A minute or two later is good. If the cathodes are too cold when applying the high anode voltage, especially at high current demands, it can strip the cathodes of their ability to provide the full performance when you need it most in the future. Small tubes, most preamp types, run on lower voltages and currents, don't suffer noticeably, and were cheap to begin with. It's the bigger more expensive tubes that standby is for. Shut down by switching to standby while the main unit is still powered on. After no more than a minute or two, fully power off the unit unless you would otherwise have to cold-start unreasonaby soon afterward. This is about 10 to 20 minutes for popular audio units, or much more if there is a true need for instant-on over a longer term. 24 hour standby is not very good for the tubes either, best fully powered off to save hours, or idling at a reasonable fraction of their ratings. On standby tubes are still more vibration sensitive than fully cold, so it's seldom a good idea to leave them on standby while there is a source of strong vibration from other sources. Never leave a tube amp in direct sunlight unless fully powered off. Standby will not save you. If it is allowed to heat up above ambient for any reason, let it cool back down to ambient before powering up. Gear that can run continuously at ambient 100degF can die at 70degF in the sun. Without the sun, different gear (including differing power bias settings on the same gear) will have different maximum ambient temperatures beyond which only short-term operation is advisable, even for units which are otherwise capable of continuous operation under slightly milder conditions. For musicians it's the class of thick-cone reinforced speakers that can take 20 or 30 minutes (near their power rating) to break in every time, that can throw you off. Speakers can not be "warmed up" silently, you have to make some noise. After this cranked-up break in, reach into an open-back cab and you feel how hot the magnets are, they were made for this but not in the sun either, especially closed-back cabinets where you can't touch the magnets but you know they're even hotter. But often it's not the warmth of the magnets (or the tubes) that makes a (beneficial) difference in the tone, it's the preflexing of the cones which makes them more articulate afterward. Most amps themselves warm up way faster than that, and can do it silently.