5 ms·
I've built several of the 2D plotters (two stepper motors, some string, some math, and blam you have you have a plotter. Most fun was sticking them on chalk boa
by ChuckMcM 10y ago
I've built several of the 2D plotters (two stepper motors, some string, some math, and blam you have you have a plotter. Most fun was sticking them on chalk boards and then using chalk in them to put some really amazing drawings up on the chalk board.
That experience has suggested that this project is not going to be as successful as they would hope. That is because you can't depend on gravity to be stronger than the angular momentum of a router bit hitting a knot in the wood. Specifically when you're routering away and you hit material that pushes back on the router, the router may not move in a gravity planned sort of way. I've seen that in the plotters when the drawing device catches on the material that its drawing on. You get a line that goes horizontal when it should go down.
These sorts of things are pretty easy to pass off when you just hang a new sheet of paper but if it means throwing out a 4x8 sheet of plywood its going to be a bit more painful.
As for discontinuous lines you put a wall sensor on the drawing puck (or the router) and when you need it to move you tell the operator. Who goes over and lifts the pen/router off the paper. The code detects the lift, adjusts to the new position while you lightly hold the puck, and then indicates you should let it back down on the surface. Once the wall sensor activates it goes back to drawing.
- BarSmith 10y agoHey ChuckMcM, I wanted to jump in here and add something. Full disclosure, It's my project. The machine is designed to print things out of the sort of manufactured sheet materials we use in most construction these days so things like plywood, sheetrock, MDF..etc. Knots don't tend to be an issue because they are only in one ply of the plywood, meaning the force is very consistent even when passing through a knot. We've never seen an issue. Materials like drywall and MDF of course don't have knots at all.
- nileshtrivedi 10y agoCan it handle printing a guitar body (wood with about an inch of thickness)?
- abakker 10y agoI would say that it depends heavily on the feed rate, expected bit life, and what wood. Soft mahogany, basswood, poplar might be done on a machine like this. I would NOT expect good results from hard, flamed maple, or other heavy, dense woods. source: have made guitar bodies on a normal CNC router. Material holding is difficult at the best of times.
- ChuckMcM 10y agoAwesome project btw! I'm glad you've not seen any issues. Re-reading what I wrote, it sounds more pessimistic than it should. I am sure everyone that uses one of these will have lots of successful "prints" and will make many interesting things.
- jacquesm 10y agoIf the problem does occur you could simply make the thing heavier and run a bit slower. Inertia is a big killer for speed but this isn't a production machine.
- tonyarkles 10y agoI wish it were that simple! On a lot of materials, going too slow will cause problems as well. You want your "chip load" to be within a band; too slow, and you'll start burning the wood instead of cutting it. http://www.pdsspindles.com/engineering-speeds http://www.pdsspindles.com/engineering-speeds I, too, do not want to come across negative about this. I'm very excited about it. If it isn't sufficiently strong to handle some types of wood, even just being able to drop a V-cutter into the router and having it very accurately draw out all the cut/guide lines is a win for the target price. If my work flow is "draw accurate cut lines, do a rough automated cut (leaving some extra around the edges), and finish on the scroll saw and belt sander", that's great!
- jacquesm 10y agoYes, obviously if you're moving so slow you're not longer cutting then that won't work but that's so slow that I highly doubt it couldn't be improved on.
- allannienhuis 10y agoSetting the rpm of the router is an ordinary setup/configuration step for doing 2d machining. I used to run 2d router systems at sign shops for years. You're always looking to optimise the speed of travel and router rpm to get the best cut qualities - fast travel with high quality cut - too fast can result in chips/burrs, too slow results in burning/melting and damage to bits, etc. I always had a list of settings to use for various combinations of materials, thicknesses, router bit sizes/types. It was a bit of a black art actually - sometimes the results of changes were counter-intuitive because of specific material properties (heat retention, etc), and that cheat-sheet wound up containing the accumulated knowledge of years of trial and error experimentation. "The only difference between Science and screwing around is writing it down" :)
- phkahler 10y agoI don't like that the ropes do not meet at a point. For any given pair of lengths, you have not entirely constrained the position of the router bit. Rotation of the hanging cradle/holder will change the position of the bit. Gravity is nice, but it seems like this problem would be overcome if the ropes met at a point coincident with the bit - or as close to that as possible. That and a Z-axis would make this a pretty cool device that I could get behind.
- ptero 10y agoThis looks like an awesome project. Do you have an idea on when Z-axis will be available? As a (single user) data point, 3D motion is a huge benefit -- if it ends up under $1000 with 3D movement I will likely just buy it to play with. Specs on accuracy would be useful, but unless it is really horrible, not likely to affect my buying decision. Good luck!
- jandrese 10y agoWould it be possible to tether the machine to four corners instead of two to avoid this potential? It complicates the pulley assembly (probably doubling it), but should make the bit more stable.
- dy 10y agoHey ChuckMcM - curious if you have any build reports of your 2D plotters. I've been very interested in them ever since seeing the Hektor and Victor project but haven't had the time/resources to build one myself (though I'd love to have one sitting at our office drawing out cool line drawings exactly as you described). http://juerglehni.com/works/viktor http://juerglehni.com/works/viktor
- ChuckMcM 10y agoNice work looks a lot fancier than what I built. This type of plotter was quite the "thing" after one appeared at the Maker Faire (I believe in 2010), I already had an EggBot[1] from EMSL and the Eggbot board[2] is set up to control two steppers. Its really easy to use, I wrote a simple Perl library for it and put it on github [3]. The "build" was really just strapping two steppers to the corners of a stand up easel board[4], hang a pen in a disk to hold it perpendicular to the page (I believe we used a 2" hole saw to cut out the "puck" and then drilled a hole in the middle for the pen (friction fit with tape for added friction). Two screw eyes at the 10-o-clock and 2-o-clock positions on the puck, a string to a spindle stuck on the left stepper, and a string to a spindle on the right stepper. Then an all night hacking session and boom, drawing pictures :-). Its really straight forward. [1] http://shop.evilmadscientist.com/productsmenu/766 http://shop.evilmadscientist.com/productsmenu/766 [2] http://shop.evilmadscientist.com/productsmenu/188 http://shop.evilmadscientist.com/productsmenu/188 [3] https://github.com/ChuckM/EggBot-Perl https://github.com/ChuckM/EggBot-Perl [4]https://www.amazon.com/Post-Self-Stick-Easel-Inches-30-Sheet/dp/B00006IA9F https://www.amazon.com/Post-Self-Stick-Easel-Inches-30-Sheet...
- IgorPartola 10y agoI remember hearing a story about a Russian tzar who was drawing plans for a railroad. He was trying to draw a straight line by holding a ruler down with his thumb. The writing utensil he used hit his thumb and went around it, creating a bump. The railroad was built perfectly straight except that one bump in the middle of nowhere. Edit: apparently this was a myth, http://bigthink.com/strange-maps/580-the-legend-of-the-tsars-finger http://bigthink.com/strange-maps/580-the-legend-of-the-tsars... It is strange that all the crap I heard as a kid and took for granted for most of my life can suddenly pop into my head and now be verified because of the internet.
- jxramos 10y agoHaha, I remember having a similar experience relating to the closing of mysteries as a kid. I remember being really mystified how a toilet and a bunch of home appliances worked. Then one day I had to fix some of them as an adult and thought, "Man this thing used to seem really mysterious and complicated as a boy".