4 ms·
Even with your first point, is the distinction really so obvious? Of course I can think of items which are obviously bolts and not screws, and vice versa, but I
by mikeash 10y ago
Even with your first point, is the distinction really so obvious? Of course I can think of items which are obviously bolts and not screws, and vice versa, but I can also think of items where I have no idea which way they would be categorized.
The document reveals some pretty subtle distinctions. For example, "An externally threaded fastener, which must be assembled with a nut to perform its intended service, is a bolt." But, "An externally threaded fastener, which must be torqued by its head into a tapped or other preformed hole to perform its intended service is a screw." Couldn't the exact same fastener fit either definition depending on the context in which it's intended to be used?
And yes, it seems your tariff theory is on point. "STEEL SCREWS AND BOLTS are classified in Chapter 73, Harmonized Tariff Schedule of the United States (HTSUS) under heading 7318. The tariff has separate provisions for the different types of screws and bolts, and separate provisions for threaded and non-threaded fasteners."
- DrStalker 10y agoYou're right, I always though my desk was held together with bolts but today I learned it uses screws!
- 4ndr3vv 10y ago> Couldn't the exact same fastener fit either definition depending on the context in which it's intended to be used? Nope. The two definitions are mutually exclusive, that's the point! Give me an example when a screw uses a nut. There isn't one, because when a fastener uses a nut, its a bolt! Give me an example when a bolt has a thread that produces from the shaft body. Again, there isnt one, as this would make it a screw.
- ghshephard 10y agoCan you clarify what you mean when you say, " thread that produces from the shaft body. " - I read that phrase over a few times, still not clear what you are saying.
- 4ndr3vv 10y agoGet a pencil, now wrap a piece of string around it. The string protrudes from the pencil "shaft body" as per a screw. Conversely in a bolt, the thread is machined into the shaft; imagine carving the line that the string made into the pencil (so that you are removing rather than adding material) to produce the thread.
- ghshephard 10y agoSo you are saying that if the threads are sunken below the shaft, then that suggests you have a bolt, but if the threads are above the surface of the shaft - that suggests screw? Now on a quest to find a screw with threads sunken into the shaft, defining said screw as something that is only tightened by applying pressure to the head.
- Someone 10y agohttps://www.boltdepot.com/Product-Details.aspx?product=1884 https://www.boltdepot.com/Product-Details.aspx?product=1884 almost is fully sunken into the shaft ("no, the shaft gets thinner" IMO is not a valid argument)
- ghshephard 10y agoBut that's a case where the threads are definitely external, not internal to the shaft. The threads are the skinny part, and they are raised above the shaft in the version you just sent.
- Someone 10y agoHow do you know whether the whole shaft was equal in width to what's now closest to the head and something was cut away or whether it was smaller to start with, and something was added? Or,is your argument that this could be a screw: /\_/\_/\_/\_ \ _ _ _ _ / \/ \/ \/ \/ but this _ _ _ _ _/ \/ \/ \/ \ \ _/ \_/\_/\_/\_/ cannot be because the outside isn't sharp enough to 'bite' into the material it is screwed into? I can see the latter holding in rubbery material that tears easily.
- Someone 10y agoFrom section 3 of the PDF: "Because of basic design, it is possible to use certain types of screws in combination with a nut" Also take a look at the "Square Head Set Screw" in section 5.4 and https://en.wikipedia.org/wiki/Screw#Differentiation_between_bolt_and_screw https://en.wikipedia.org/wiki/Screw#Differentiation_between_.... [also: https://en.m.wikipedia.org/wiki/Screw#United_States_government_standards https://en.m.wikipedia.org/wiki/Screw#United_States_governme... explains why the government needs to define this: different tariffs. That page also mentions "In 1991 responding to an influx of counterfeit fasteners Congress passed PL 101-592[12] "Fastener Quality Act"". Apparently, screws/bolts got imported as bolts/screws]
- mikeash 10y agoTake a threaded fastener and insert it into a threaded hole. By the definition given here, it's a screw. Now remove it and put a nut on the end instead. By the definition given here, it's been transmuted into a bolt despite no physical changes to the item itself.
- PeanutNore 10y agoWhen you put a nut on a machine screw it doesn't cease to be a machine screw, but it works and I do it frequently. However, the document accounts for this in section 3: "Because of basic design, it is possible to use certain types of screws in combination with a nut. Any externally threaded fastener which has a majority of the design characteristics which assist its proper use in a tapped or other preformed hole is a screw, regardless of how it is used in its service application."