3 ms·
This is great! Here's my (more retro) take on it: https://www.stavros.io/posts/irotary-saga/ https://www.stavros.io/posts/irotary-saga/ I'm looking to make a
by StavrosK 10y ago
This is great! Here's my (more retro) take on it:
https://www.stavros.io/posts/irotary-saga/ https://www.stavros.io/posts/irotary-saga/
I'm looking to make a PCB for it, as the Arduino Uno + shield is way, way too big for this. Does anyone know of a good way to do that? I looked at the SIM900 module but I was a bit intimidated by all the pins.
The OP's build seems to be using the Quectel M10, maybe it won't be too hard to get that running...
- pjc50 10y agoYou won't need all the pins, but these modules are fussy about power and you need to route the antenna properly.
- StavrosK 10y agoYou're quite correct. I'm going to use a 5V regulator, which seems to do the job very well on the shields I've seen, so power shouldn't be a problem. The antenna is going to be an issue if I want to make it a track on the PCB, as I have no idea how to route antennas. Does it only have to be a specific length? KiCAD has tooling to help that. Otherwise, I can just stick an external antenna on it, like most shields have.
- pjc50 10y ago5V regulator is not correct, that would be too convenient: the module datasheet says "3.3~4.6V 4.0V nominal". They're designed to be driven directly from a LiPo battery (via short leads with appropriate decoupling, power draw is very spikey). The Arduino shield has a LMZ12002TZ switchmode chip on it. The routing from the device to the antenna needs to be controlled impedance, ie specified width and distance from ground planes. You'll need to leave a ground plane cutout round the SMA connector. Actually building a PCB track antenna requires specialised software voodoo to get right, especially if you want to retain multi-band capability. (My experience is with a different module with identical specs; we found that 4.8V caused no obvious problems except that maybe 1 in 10 firmware downloads would irrevocably brick the device).
- StavrosK 10y agoOh hmm, thank you for that information, it's very useful. I do run it from a LiPo battery, so hopefully that will work well after I decouple it (with what I'm guessing should be a rather large capacitor). As for the antenna, the SMA route sounds much easier, so I'll probably do that. As for firmware downloads, I pretty much only need the device to make and receive calls, so I shouldn't need to upgrade the firmware much past the first time. Thanks again for the info!
- willyyr 10y agoThe Hipsters of Berlin and elsewhere in the world will love this. You should sell it :)
- StavrosK 10y agoEverybody has been saying that, but I can't be bothered :P Maybe I will, if I can make the PCB version, since that would be much easier to assemble.
- wolfgke 10y agoThe guys of the Fablab Hamburg in Germany already created a PCB from it and used it produce a low volume of cell phones from it. Just ask them politely for the PCB. Here two German articles about the initiative: http://www.heise.de/make/meldung/Temporaere-Handy-Fabrik-in-Hamburg-2267612.html http://www.heise.de/make/meldung/Temporaere-Handy-Fabrik-in-... http://www.heise.de/make/meldung/Handy-Selbstbau-Projekt-in-Hamburg-bestuecken-backen-telefonieren-2294509.html http://www.heise.de/make/meldung/Handy-Selbstbau-Projekt-in-...
- StavrosK 10y agoHmm, this seems to be the exact same PCB mentioned in this post (and with the same module). Routing the PCB isn't really the hard part, it's mostly figuring out how the pins need to be connected. The datasheet is pretty long, but I'll buy a bare module now and try to get it working.
- nickpsecurity 10y agoYour project and trailer was awesome. Love that you brought back the experience of slamming the phone on some prick. Especially after all the work the user goes through dialing the number. Outrageous that the other party didn't appreciate the call! Haha. Also, what was once ancient is now innovative. :) EDIT: Rewatching the trailer, I just noticed a new feature you can add to your marketing material. The Redial button gives the prick a second chance with one press. Still a prick? Slam! Again! Redial-slam should be considered an extra feature given it's used for specific situations & hard with regular rotary.
- StavrosK 10y agoHaha, thanks! I actually need to add the redial feature to my post, with that exact use case. "redial Hey, I just called again to see if you're still an ass. Yes? slam, redial Oh, also, screw you for having three zeroes in your phone number! slam"
- bla2 10y agoVery cool, thanks for posting.
- StavrosK 10y agoThanks, I'm glad you like it!