5 ms·
Pi Zero consumes about 80 mA when idle. An Arduino Pro Mini can do an order of magnitude better, and that's without getting fancy with sleep modes and a watchdo
by tzs 11y ago
Pi Zero consumes about 80 mA when idle. An Arduino Pro Mini can do an order of magnitude better, and that's without getting fancy with sleep modes and a watchdog timer. For things where most of the time is idle, and so you can have the Arduino spend most of its time in a very low power mode and just wake up when it is time to read a sensor or adjust a control or something like that, you can do something like on average three orders of magnitude better than the Pi Zero. (Four orders of magnitude if you do a little hardware hacking on the Arduino).
That's the difference between having to change a couple AA batteries every day or two (Pi Zero) and running for a year off of a coin cell (Arduino).
Here's an article on power consumption of an Arduino Pro Mini: http://www.home-automation-community.com/arduino-low-power-how-to-run-atmega328p-for-a-year-on-coin-cell-battery/ http://www.home-automation-community.com/arduino-low-power-h...
Here's one on Pi Zero power consumption: http://www.jeffgeerling.com/blogs/jeff-geerling/raspberry-pi-zero-power http://www.jeffgeerling.com/blogs/jeff-geerling/raspberry-pi...
- ant6n 11y agoI wonder whether it would be possible to create a tablet/laptop with an e-ink display, where the processing switches between a low-powered ARM and something like an Arduino. When the Arduino is used, the ARM would be turned completely off.
- striking 11y agoThat's the thinking behind the big.LITTLE concept, and it's in use today. It's nice because in addition to power savings, it doesn't take up as much of the PCB as an ARM+Arduino combo would.
- masklinn 11y ago> I wonder whether it would be possible to create a tablet/laptop with an e-ink display, where the processing switches between a low-powered ARM and something like an Arduino. You'd have to deal with different architectures and a lot of headaches, but it's the idea behind ARM's big.LITTLE, where you pair high-perf high-power and low-perf low-power cores. So your tablet's SoC might have a ~200mW A53 for mostly-idle use with a ~1W A72 for more active "high-performance" work loads. And the only additional hardware is the additional cores and the interconnect, the SoC is shared between "low-perf" and "high-perf" cores, which probably wouldn't be the case for an arduino/arm mix.
- ant6n 11y agoTrue. But ~200mW is still a fair amount, compared to, say ~20mW of something like the esp8266.
- janjongboom 11y agoApple does something similar, uses a ARM M-series microcontroller to do sensor readings (activity detection etc.) when the device is sleeping [1]. [1] https://en.wikipedia.org/wiki/Apple_motion_coprocessors https://en.wikipedia.org/wiki/Apple_motion_coprocessors
- hyperpallium 11y agoI understand the power savings of e-ink go away when you update often eg typing, scrolling. Maybe that can be worked around? eg if updating only a small area. Or as a second display for docs.
- jschwartzi 11y agoIt depends quite a bit on how the screen is updated. If it's like a traditional raster image, then you have to clock out each individual pixel in the image along with some blanking periods. The controller on the display is then responsible for taking that pixel data, syncing on the blanking periods, and drawing lines of pixels whenever data enable goes high. If the eInk display doesn't use this raster model but rather an addressing model then it might be possible to support partial updates. I doubt very much that it does though.
- lee_s 11y agoEink uses a raster mode, but with (somewhat) tri-state pixels. You can send a 'no change' to any particular pixel. The disadvantage is you still need to scan the entire screen, so it isn't really useful for changing individual pixels, but partial updates are common. The other difference from a traditional raster display is there is no minimum refresh rate. Eink controller chips use an addressing model and handle the partial updates for you, so the main processor sees a bare framebuffer.
- ant6n 11y agoNote the link I submitted above, where it says that yes you have to send all rows with every refresh, but for every row you can tell it not to do anything. Presumably that means if you skip all but few rows, you'll get a faster update.
- ant6n 11y agoApparently you can do local updates, i.e. update a particular row. At least on the 6.7" e-ink that the Kindle uses: http://www.essentialscrap.com/eink/waveforms.html http://www.essentialscrap.com/eink/waveforms.html
- lee_s 11y agoThis does actually somewhat exist now. Most modern phones/tablets/ereaders have a low power core for monitoring and sleep modes. The problem is as soon as you want to 'do' anything you need the performance of the main core. Especially anything with graphics (like eink). The Arduino is underpowered for anything more than a supervisory role, and even those applications are tending towards Cortex-M series.
- RealityVoid 11y agoHow would the wdog timer impact sleep?
- antoniuschan99 11y agowhat about esp8266-01. It can go to sleep mode and consumes very little power plus it has wifi built in?
- anotheryou 11y agoWow, pro mini looks exactly like a teensy. They sould really show some attribution to the original hardware designers... see also: https://arduinohistory.github.io/#when-did-arduino-begin-and-why-werent-you-a-member-of-the-arduino-team https://arduinohistory.github.io/#when-did-arduino-begin-and...