3 ms·
I think it would be fascinating if some of the older fab processes could be democratized and people could start experimenting with chip fab at home. Perhaps som
by moron4hire 11y ago
I think it would be fascinating if some of the older fab processes could be democratized and people could start experimenting with chip fab at home. Perhaps some tech out of the 3D printing field would be adaptable. No, you're not going to make something blazingly fast, but imagine printing your own ATMEGA328P or MSP430 or even 8086 clone.
- 0xcde4c3db 11y agoThe older fab processes involved some pretty nasty chemicals. I seem to remember that hydrofluoric acid is used in multiple steps (to make contact cuts through oxide layers?) . To give you a broader idea, a former MOS Technology / Commodore fab ended up as a Superfund site [1]. [1] http://cumulis.epa.gov/supercpad/cursites/csitinfo.cfm?id=0301146 http://cumulis.epa.gov/supercpad/cursites/csitinfo.cfm?id=03...
- jacquesm 11y agoWe have a couple of similar sites here in NL, projected clean up time in the 100's of years. Very bad legacies from the time when the environment wasn't even on the radar of most governments and companies dumped their waste with abandon.
- Gibbon1 11y agoI think running mixed lots of wafers is still a thing. However besides still being very expensive the other two issues are the software tools to lay out the chips. And then the cost of making the masks[1]. Friend of mine was working for a startup five years ago I think he said they needed 2.5 million for a small team + initial fab. If you are interested you can get into programming FPGA's for a few grand at most. Far as I can tell looking on the outside of people doing both it's almost the same minus the chip layout manufacturing step. Also the design cycle time is hella faster and cheaper. [1] I have no idea what masks cost now, but 15 years ago the company I worked for needed to change a metal mask and it cost $50k, I think a full set was $250,000.
- trsohmers 11y agoI'm the founder of a startup taping out of first test chip in May... Getting 100 chips back on a shuttle run (Also known as a multi project wafer, where mask costs are shared by multiple companies) will cost us around $250,000. That is just the cost of these first 100 chips. Mask costs for a modern (eg 28nm) process start at about $2 Million, and go up from there pretty quickly, but is based on a lot of factors. Once the masks are made though, it is roughly $5K a wafer (where you can have 100s of dies on a wafer.
- elbigbad 11y agoThis sounds really interesting. I don't know what too much of this means though. Can you recommend books or in depth articles about the process of ic making?
- nickpsecurity 11y agoThe Wikipedia articles on semiconductor manufacturing are pretty good. Far as ASIC's, I struggled a while to find a great resource on all aspects of design, verification, and prototyping. Here's the best one I found for you: http://cc.ee.ntu.edu.tw/~ywchang/Courses/PD/EDA_Chapter1.pdf http://cc.ee.ntu.edu.tw/~ywchang/Courses/PD/EDA_Chapter1.pdf On top of that, there's the cost of the photomasks that print the samples for testing (and later production). They range from tens of thousands on oldest nodes to millions on newer ones. Every time you screw up and change the design you buy another mask. Hence, avoidance of new nodes by low volume groups, design/verification tools that can cost $1mil/yr a person, and heavy re-use of components. One trick that's popular is called multi-project wafers: a mask and chip run that's shared by several people with high cost split among them. This is available through groups like MOSIS and X-Fab. Lets you test your design in [more] affordable pieces. Plus, tooling and overall cost has come down for older nodes which are still highly usable for many scenarios: http://gsaglobal.org/forum/2009/1/articles_full_double.asp http://gsaglobal.org/forum/2009/1/articles_full_double.asp Open tools are getting there slowly but not reliable or competitive enough. Here's the only open flow I know of: http://opencircuitdesign.com/qflow/ http://opencircuitdesign.com/qflow/ So, overall barrier to entry for ASIC design is expensive expertise, high-cost of proprietary tools, and cost of masks (or MPW's). Going cheap on all these still gives several hundred thousand for a useful design on a good node. Simpler, single-purpose chips on oldest nodes can be less than that, though. Here's an example: http://www.planetanalog.com/author.asp?section_id=526&doc_id=559519 http://www.planetanalog.com/author.asp?section_id=526&doc_id... Hope all this helps your understanding of the situation.
- yuhong 11y agoRecent HN story about exactly this: https://news.ycombinator.com/item?id=10723305 https://news.ycombinator.com/item?id=10723305