4 ms·
Haha... I have that _exact_ pedal on my board. Overall, not bad if you want something cheap... Couple of complaints: Things get muddy fast, you really have to p
by exabrial 11y ago
Haha... I have that _exact_ pedal on my board. Overall, not bad if you want something cheap... Couple of complaints: Things get muddy fast, you really have to pair it with a compressor to control your input volume for things to be any good. Next, there's a massive volume difference between the hot and warm modes. You can't flip between them without need to adjust the volume knob. Finally, there's a distinct lack of bass in the "hot" mode. Other than that, it's not terrible, just don't expect a ton and it's not too bad!
- mb_72 11y agoThe kind of problems you've mentioned are typical of thoughtless "what a cool mod!" changes to a design; these often ignore practical issues such as the volume change you've mentioned. However, 'fixing' these issues would require a bit more work and a few more parts, attributes that seem commonly not to be important in low-end pedals. But, yeah, good for starting players (although even then I'd recommend a cheap multi-fx unit); beginners often don't even know what certain effects are, and once you know enough to feel you need a 'proper' version of effect you're better off getting something this is a step or two up from the cheapest available. (disclosure - part owner of Prophecysound Systems)
- cushychicken 11y agoYeah, I suppose if you wanted to do the extra bass mod right so that your volume level is mostly the same when going "hot", you'd also need to tweak the series resistor value as well to get the gain of the snubber to match up. Guessing you'd probably also want to drop down that parallel 470k as well.
- ricardobeat 11y agoDoes the original have the same issues?
- exabrial 11y agoNot exactly... It might be my hum buckers causing the muddy sounds well then volume gets too hot. I don't have a TS808 I can compare apples to apples with. The volume change problem and the lack of bass aren't problems for the TS808 because it was hardwired for the "warm" mode with no selector switch. Google is telling me the Boss BD2 doesn't have the toggle switch either.
- cushychicken 11y agoReduced gain in the lower frequencies is a feature, not a bug, of the original TS808 circuit. It was meant to keep the distortion from getting muddy. The original clipping stage includes a little resistor/capacitor snubber that rolls off frequencies below ~720Hz.
- ableal 11y ago> Next, there's a massive volume difference between the hot and warm modes. If I read the text and schematics correctly, that's because one uses 0.7V silicon diodes and the other 1.7V LEDs in the opamp feedback loop. (At least red LEDs used to be 1.7V when I was messing with them.) So that should clip the voltage in that branch to +/- 0.7 or +/- 1.7 volts, hence the power difference if nothing else is moderating it.
- cushychicken 11y agoThe turn on levels I measured were much smaller in discrepancy than that; the silicon diodes were clipping at 0.55 V, while the LEDs were only slightly higher, at about 0.8 V. Made me wonder if I was measuring them incorrectly.
- ableal 11y agoThat sounds OK, if a bit low. Perhaps the resistors are large, or you might be diverting some current through a low(ish) impedance voltmeter, but those should be rare nowadays. The trick with diodes is that the curve is exponential - so for a "0.7V" diode, and pulling numbers out of the air, you can get 0.3V for nanoamp currents, or 1.0V for power-station currents (for the brief moment before it melts ;-) The real equation is very simple, if anyone wants to play. For instance, it's well explained here, midway down the page: http://www.allaboutcircuits.com/textbook/semiconductors/chpt-3/introduction-to-diodes-and-rectifiers/ http://www.allaboutcircuits.com/textbook/semiconductors/chpt...
- cushychicken 11y agoThat's a good point; the DMM I used could have just been extrapolating "turnon" to a certain current. I'll have to check the DMM's specs.